Dewalt Tools & Hardware - Others - Recent Questions, Troubleshooting & Support

I have the same problem with a Porter Cable orbital sander I recently purchased. Whats happening is the sander is catching the edge of the board you're trying to sand and jerking back and forth as the sander base spins. It seems that if the board your're sanding is at least as wide as the sander base, the problem goes away, which does little good because there will be many times I we'll need to sand wood that is less in size. But you may try using a lesser grit sandpaper and see if that alleviates the problem somewhat.

faulty or dirty connections

Yes

here is a link copy and paste https://sawmillcreek.org/showthread.php?111567-DeWalt-733-Rollers-stopped-moving ..

Most body shell panels on power tools are put together in a set order and often have one or more hidden screws. These are sometimes hidden behind stickers. Other sections are sometimes held it place by hook clips that are moulded into the plastic panels. These need to be Gently levered apart. DO NOT force any sections apart as this will damage the shell making it unsafe to use.

It needs new blades - likely has a chip in one. See link for replacement tutorial

Hold down the ( V ) button while powering the unit on. THe puts the unit in cal mode for the Y axis. Hold down the up button while powering on the unit, this puts it in cal mode for the X axis. that is as far as I have gotten.Paul

Red is pos and black is neg.

Those with larger bit shanks can hold larger blades. For large joinery cuts, buy a router with a large bit-shank diameter.

Hello,
I did not understand all you said but I think you are not using right nails (16 ga. Angled paslode nails)

https://www.weeklytools.com/dewalt-angle-grinder-buying-guide/ When it comes to Angle Grinder, the name of the Dewalt tools maker comes first. We will look at the basic parts and functions of a grinder before purchasing a machine. Then let's see the details without delay.

https://www.weeklytools.com/different-uses-for-an-angle-grinder/ An angle grinder is a multifaced handheld power tools that was invented by a German company. We may don't know a lot about this tool because it is an unrecognized instrument like some other tools. Now we will discuss different Uses for angle grinder. An angle grinder is also known as a side grinder or disc grinder. It is a machine with a rotating abrasive cutting disc. Angle grinders can be powered by an electric motor, petrol engine, or compressed air. It comes in a wide variety of different sizes and powerful motor, each with the other purpose. Once anyone knows about these, he can easily find out the best angle grinder for his needs. Angle grinders are quality fulled equipment for any metal fabrication shop, and those are typically used in auto repair, workshops, and construction sites.

https://www.weeklytools.com/how-to-use-a-nail-gun-with-an-air-compressor/ We may not need a drill machine almost the whole time. But there is a demand for a pilot hole during the home finishing process. This post is not for you if you are a professional. However, in most of the cases, we observe the necessity for a pilot hole. From wooden doors and windows ...

There are two adjustments. First find the screw on the right side that allows loosening of rear baseplate. Once loose, another screw jacks the base up or down. They are both hex heads on mine.

Turn jack screw until a straight edge along the base just clears the cutter. Spin the cutter once to make sure both edges are the same depth and that both clear the straight edge.

For the front shoe, turn adjustment handle to zero. Remove the adjustment handle from the front shoe and find two vertical slots at the front. Two screws (hex heads) allow loosening of shoe. Once loose, the shoe can be adjusted by sliding up or down. With a straight edge held along the rear base and touching the front base, align the front shoe so straight edge barely clears blade and tighten screws. The front and back base should line up. Replace adjustment lever and recheck zero cut clearance as well as maximum depth. Readjust as necessary. If zero clearance is not an issue, the bases can be set to allow deeper cuts than factory specified. It's a powerful planer so if you're cutting softer woods, a deeper cut might be desired.

Hi,
Sounds like a battery contact problem or a bad battery..

Here is a tip that I wrote about the Paslode nailers and the problems that can come up with them.

I also have a link to the Paslode manuals which contain Paslode cleaning and troubleshooting guides.

If you need parts for your Paslode, there also is a link for a site that sells the Paslode nailer parts.

Paslode Cordless Nailer Problems

heatman101

I’m not trying to be a wise guy but the regulator has an adjustment on the bottom

Its the compressor... not enough pressure.

The nailer must be firmly pressed against the surface you are planning to nail. This will arm the nailer in preparation for firing the nail.

Try this link: https://www.ereplacementparts.com/dewalt-dw423-type-inch-evs-random-orbit-sander-parts-c-1009_2742_2758.html

https://www.2helpu.com/PDMSDocuments/EU/Docs/Service%20Dossier/DW733-D.PDF