D-Link Computers & Internet - Page 5 - Recent Questions, Troubleshooting & Support

Try another power adapter.

Most likely you have damaged the D-Link router.Connect a correct power adapter to the D-Link to see if it works properly, if it doesn't work then you need to purchasr a new wireless router.

Hi,

To clear cache manually try the following:

(1) start dos console by going to start > run > type "CMD" and press enter
(2) then type IPCONFIG /FLUSHDNS

If the above doesn't work then try the following THEN do the above step again:

~ Enabling DNS Cache Service ~

• To start the WinXP DNS Cache Service, click START -- RUN -- SERVICES.MSC -- Press ENTER.

• The Services console will appear.
• Navigate down the list of services until you find the one labeled DNS Client.
• Double click on DNS Client to open its properties pane. Set the Startup type to AUTOMATIC.
• Click APPLY and then click START to start this service.
• Retry the above step to manually clear your DNS Cache.
Thanks.

try to check ur cable type

Our technical expert solves more than 500+ issue every day. we are available in every unapproachable location of USA/Canada. The customer can contact us any time, our technical staff always ready to solve your all issue. Therefore if you are facing any kind of issue which is mention above so don't need to worry about it just Dial our Toll-free Number D-Link Support Number USA 1-833-284-3444. https://servicenumber.org/d-link.html

Dowmload the manual from this link
http://safemanuals.com/user-guide-instructions-owner-manual/D-LINK/DI-614--_E

Sownload the driver from this link
http://drivers.soft5000.com/subcat_359.html

Thanks, Do Not forget to rate

avastph

Go to dlink.com and go to FAQ, "D-Link Systems DIR-600L Wireless-N150 Cloud Router setup" and you will find a S-B-S how to.

Yep. No problem. Step by Step right here.

http://portforward.com/english/routers/port_forwarding/Dlink/DI-624/Xbox_Live_360.htm

you don't need to install a router on a PC. The wireless card or ethernet cable should talk to the router.

try admin/di-624. where "di" may be capped.

i do not have wep option in my wireless settings

There is a rest port on all drinks. You need a paperclip ir something similar to depress.hold down for a count I 5 5 1000 s and then lights will blink and reset.

hi, I think you may try WPA2+AES setting while setting up wireless connectivity, it will ask network key to setup. It is more secure setting for wireless usage.

That could mean the system is not booting correctly. If the admin page is not accesible, the wifi is not working and no LED is glowing when you plug an ethernet cable to either in LAN or WAN port, you'll need to reset the router (you will loose all your settings) to the factory settings.
You'll need something thin, needle or a pen, the reset button is on the back side near AC plug, push and hold the button until the LEDs start blinking randomly (usualy 20 to 30 seconds).
Then follow the steps in the manual from manufacturer, you'll how to setup the router as you had to when you bought it as new.

First check the LAN cable between the devices and try another cable. Reboot both devices. The final solution is a factory reset of your router. You can do a factory reset by logging into the router using you browser. Go to the settings and perform a factory reset If you forgot the router password, you ill have to do a factory reset by locating a small hold on the back of the router and insert the tip of of paper clip for about 10 seconds while the power is on. The router will be reset to out of box status and then you can set-up form scratch.

WHat is happening is the flash memory on the router is currupt and can't be reflashed.


I was finally able to reflash the device, and after I did same problem again. But this time only the basic firmware page comes up.(when the flash is currupt)

ANd every time I try to flash the new firmware it fails.

If the power pack is good then the router is dead and needs to be replaced. It's generally cheaper than trying to fix it.