Crown Audio Players & Recorders - Answered Questions & Fixed Issues

I would study the service manual and service notes to find out why the temperature sensors do not work. Probably a supply rail down I would think to affect both of them.

Question edited for a lot more clarity. Question moved from Cars and Trucks Category. Take it in for professional repair unless you have the test equipment. https://www.google.com/search?q=Crown+XLS+2502+drive+core+repairs ...

The Power Crown XTi 6000 is a power amplifier, and it sounds like it is activating its protection circuit and not generating a Pulse Width Modulation (PWM) signal. There could be a few different reasons for this behavior. Some possible causes include:

• Overheating: The amplifier could be overheating, causing the protection circuit to activate in order to prevent damage.
• Short circuit: There could be a short circuit in the amplifier, causing the protection circuit to activate.
• Input signal issue: The input signal to the amplifier could be causing the protection circuit to activate. This could be due to a problem with the source, such as a malfunctioning mixer or a disconnected cable.
• Output impedance or load mismatch: The amplifier may have a mismatch in output impedance or the load impedance which can cause the protection circuit to activate.
• Firmware or software issue : There could be a problem with the firmware or software that controls the amplifier, causing the protection circuit to activate.

Without more information, it's difficult to say for certain what the problem is. It's recommended to check the manual for troubleshooting steps and also check for any possible firmware updates. If problem persist it's recommended to take professional help.

Crown xti 6000 low input problem

Not most service manuals can be downloaded unless you use a model close to the original. Try service manuals.com

It will be the boost cap near the power switch. 220if 35v. In fact 3 caps die which kill XTi and CDi series. Amps. 2 x 220ugf and one 470 uf. All. Located yon the freuont right edge of the main PCB. An actual crown tech

- Use your favourite search engine (Webcrawler is dandy) and type your question/info into it. - SEARCH ENGINES ARE YOUR FRIEND!!! Type in keywords and check the results. - I'm not an expert but it almost sounds like maybe a speaker relay or whatever on the amp has bailed out. Good Luck :) R

It could be a defective switching element but more likely something has failed in the right channel amplifier chain such as a a component or amplifier stage.

Hello Anonymous, Here are 2 links to Harman ( Crown ) Support and Service Manual. Crown suggests you call their tech support First to determine the need for repair. Best of Luck, JP https://3e7777c294b9bcaa5486-bc95634e606bab3d0a267a5a7901c44d.ssl.cf2.rackcdn.com/product_documents/documents/2862_1433871166/XTi_Series_Service_Manual_original.pdf https://www.crownaudio.com/en/support

Google should have a manual for your 1000 amp thermal and also try on the companies official website too for a manual. Try searching on YouTube as well and YouTube should have videos about amp thermal on - Crown Audio Players & Recorders

http://www.fixya.com/tags/crown_amplifier_fault

Probable power transistor failure.

If you have eliminated any shorted speakers, cables etc, then the only other cause is a shorted device on the power output board. Probably a device on the heatsink.

Possibley bad windings on the transformer. Not enough or bad insulation.

Hello, Sylvia - I have no idea what entity you meant to receive your question. You posted in the Fixya.com website, which is intended for asking and answering questions on how to go about REPAIRING THINGS. Plus, your question landed in the Fixya category for Crown (brand) Audio Players & Recorders. Perhaps you meant to message Netflix, or your local public library, or a person from whom you borrowed the DVD, or someone to whom you sold the DVD, or . . . Best wishes.

Is the fan supposed to be on. On some units it runs all the time on others when the temp hits a certail level. Which is it for your baby?

IT SHOULD BE 0000

It's best to assume there is a short circuit in the power amp board. The unit is going in to protect mode to stop it blowing fuses etc. Could be caused by bad speaker wiring or connections by the way.

Try downloading from google.

Component over heating . Main input output ic defective.