I'm sorry to hear about the issues you're experiencing with your Canon imagePROGRAF W6400 printer. It sounds like there may be some problems with the ink system or the printhead. Here are a few troubleshooting steps you can try:
1. Verify compatibility: Ensure that the compatible cartridges you purchased are indeed compatible with your specific printer model. Double-check the packaging or consult the manufacturer's documentation to confirm compatibility.
2. Clean the printhead: Ink flow issues can sometimes be resolved by cleaning the printhead. Refer to your printer's manual for instructions on how to perform a printhead cleaning. It typically involves accessing the maintenance or ink settings on the printer's control panel.
3. Check ink levels: Use the printer's control panel or software utility to check the ink levels of the cartridges. If they still show as empty or low despite being newly installed, there might be an issue with the ink level sensors or the cartridge installation. Ensure the cartridges are properly seated and making proper contact with the printer.
4. Update firmware and drivers: Visit the Canon support website and download the latest firmware and drivers for your printer. Outdated firmware or drivers can sometimes cause compatibility or functionality issues.
5. Contact Canon support: If the above steps don't resolve the problem, it's recommended to reach out to Canon support for further assistance. They can provide specific troubleshooting steps based on your printer model and help determine if any repairs or replacements are necessary.
Remember to provide detailed information about the issue, the steps you've already taken, and any error messages you're encountering when contacting support. They will be better equipped to assist you in resolving the problem.
I hope these suggestions help you get your printer back up and running smoothly.
This might help
The paper jam error code for the Cannon iR7200 is 238. It indicates that there is paper stuck in the printer's paper feed route. Open the front access panel gently and take out the pieces of jammed paper to clear the paper jam. Look for any pieces of paper that may have become stuck in the paper feed channel and take them out. Before attempting to unclog the paper jam, unplug the power cord.
The Cannon Imagerunner 330S has been discontinued for over 20 years, so it may be difficult to find a replacement feeder for it. I recommend contacting Canon's customer support to see if they have any parts or suggestions for repairing the feeder. You can also try checking with local repair shops to see if they have any compatible parts available. Contact information for Canon's customer support can be found on their website.
Check to make sure there isn't something blocking the paper output on the back of the computer. If not, open up the front door, about the top drawer, and close it. Go the back and open up the rear cover and close it. That may reset the problem. Remove ALL jobs from the queue and clear the set memory.
If that doesn't fix it, there may be a problem with the output sensor. These sensors may not be easily available on any website, so it's best to call you local Oce/Canon dealer for service.
The Canon printer Error 6800 can occur due to a general glitch that prevents the printer from being able to load its configurations properly.
Methods to fix the Canon printer 6800 error code:
·Restart the printer
·Reset the printer settings
·Clean the printer ink cartridges
·Contact canon printer experts
Also read the more solutions to fix the canon printer error codes.
I'm sorry to hear that you're having trouble with your Canon G7000 printer. Here are the steps to change the paper source from the rear paper feed to the front paper cassette:
Make sure that the printer is turned on.
Open the paper output tray and the front cover.
Slide out the paper cassette located at the bottom of the printer.
Press the release button on the back of the printer and pull out the paper support.
Slide the paper guides on the cassette to match the size of the paper you're using.
Load the paper into the cassette with the print side facing down and the top edge going in first.
Insert the cassette back into the printer until it clicks into place.
Close the front cover and the paper output tray.
Once you've completed these steps, your printer should automatically detect the paper cassette as the paper source. If you want to switch back to the rear paper feed, simply repeat the process but select the rear paper feed option instead.
I hope this helps! If you continue to have issues, please let me know and I'll try my best to assist you further.
well it does not like the A4 sized paper for 3 reasons/
1; A4 paper not there.
2: the sensors there A4 are bad or just dirty.
3: or the software for printer is corrupted , reload it?
printers love to fail that is what the love to do, google it. see billion hits for 50 years deep. Love to fail
so a wise owner does a full cleaning of the printer print pathes
and all sensors blown clean with (shop air or CAN-O-AIR)
or calls for service, locally'
