Cadet Manufacturing Home - Recent Questions, Troubleshooting & Support
Flushing problem with American Standard toilet model 2474
American Standard 2474016.222 also had the same problem mine had two discs apparently on efrom factory perhaps and one from the floating disc that must have fallen off I used a screw to get them out adn drained as much water as possible then went back and forth adding water a little at a time and then using a tolwel to sponge the water out (no shop vac around) After findign one I then found the other. This post saved me sooo much money adn I have dealt with the intermittant problem for years in this spare bathroom THANK YOU SO MUCH
10/19/2010 3:19:18 AM •
Cadet...
•
Answered
on Oct 19, 2010
Tank serial # looks like this? S 00
that is a Kohler model 4520<br />
the other numbers are for manufacturer codes.<br />
<br />
is this an older toilet? Kohler discontinued that model.<br />
<br />
<a href="http://www.designtool.kohler.com/us/detail.jsp?item=9654702">http://www.designtool.kohler.com/us/detail.jsp?item=9654702</a>
8/31/2010 5:51:36 AM •
Cadet...
•
Answered
on Aug 31, 2010
We just replaced out toilet because we had no
its got a blocked down pipe lime scale will do this to you, the only way to sort it out is strip it out completly and give it a good clean, if that still failes to flush then its the flushing pump needing looking at,
10/25/2009 3:39:50 PM •
Cadet...
•
Answered
on Oct 25, 2009
Can't locate serial number
get a mirror and look behind the toilet by the rim, under the tank and inside the tank above the water line
8/3/2009 1:18:44 AM •
Cadet...
•
Answered
on Aug 03, 2009
My harness pipe broke on my whirlpool
Yes it can. Buy a coupler and some PVC cement at a supply store. Cut enough off each end of the break to insert cleanly in a dry fit. You can use a hack saw. If the fit is ok, the clean all around both edges of the pipes with purple primer. Then apply cement on one end of the pipe and inside the coupler. Push the coupler onto the pipe until you feel it bottom out. Hold it in place a nimute or so. Repeat with the other side. Allow it to sit overnight and dry thoroughly and refill with water.
6/4/2009 12:00:51 PM •
Cadet...
•
Answered
on Jun 04, 2009
My Pressure Assisted toilet does not have the power to flush
Found this on this same site...Please let us know is it works (I'd like to know since I'm considering a pressure-assisted toilet).
Solution #2
posted on Apr 21, 2009
Asker's Rating
nanotick
Rank: Apprentice
Rating: 0%, 0 votes
This type of flush system can be re presurised quickly by holding down the flush handle for about good 2 minutes, then release , wait for the tank to be refilled with water.
Now you can flush away your inner rotting mess down tube good-by...
5/14/2009 2:45:25 PM •
Cadet...
•
Answered
on May 14, 2009
What are the different types of powder coating?
Thermoplastic and thermoset are the two types of powder coatings used by leading
Powder coating services. Thermoplastic coating don't undergo any chemical change when heated. Therefore they can be softened and hardened by heating repeatedly. Unlike thermoplastic coatings thermoset coatings changes into infusible materials on heating. Nylons and vinyls are thermoplastic while acrylics and polyesters are thermoset.
4/24/2024 12:02:34 PM •
Home
•
Answered
Yesterday
What is a meat tenderizer?
This is used to tenderize meat before you cook it. It makes the meat easier to chew and digest. You can also use it before you boil or fry meat. You can do this mechanically, with something like a meat mallet that cuts up the meat fibres. You can do it thermally by putting the temperature really high to break down the connective tissue of the meat. The last method is enzymatic and uses enzymes to break down the collagen. This method is either slow with dry-aging the meat or you can use fruit to marinate the meat.
4/16/2024 6:28:01 AM •
Home
•
Answered
on Apr 16, 2024
Lost half of my jets on one side of the tub only.I have tried closing the jets that do work half,does not make a difference to the jets not working.Would it be best to empty the tub and start over?
it's likely due to an air lock. Here's what you can do to resolve this issue:
Manually Clearing an Airlock:
Run the jets on low for about 30 seconds.
Then run the jets on high for another 30 seconds.
Repeat this process 3 or 4 times.
If you hear a gurgling sound and see air bubbling up, continue running your hot tub until it pushes all the air out.
If this doesn't work after several attempts, try a different approach.
Bleeder Valves or Pump Method:
Some spas have bleeder valves that allow you to bleed air out of the lines.
First, turn off the spa at the breaker.
Access the pump and loosen the valve to allow the air to escape.
When the air has bled out (you'll notice it turns from hissing air to a stream of water), close the valve.
Run the pump to ensure the jets are now pumping water as expected.
Why Are the Jets Not Working on One Side Only?:
Many hot tubs have two water pumps.
If the jets on only one side of your hot tub stop working, there could be an airlock in only one of the pumps.
It could also be a blockage in the jet lines for that side or a problem with the internal mechanism of the jet itself.
Can You Use a Spa with an Airlock?:
It is not recommended to use a hot tub with an airlock.
4/3/2024 4:33:08 AM •
Home
•
Answered
on Apr 03, 2024
Restarting my marcel hour strike quartz clock nrms603.
To restart your Marcel Hour Strike Quartz Clock NRMS603, follow these steps:
Stop the Pendulum: Gently stop the pendulum from swinging by holding it still.
Remove the Battery: Open the clock case and locate the battery compartment. Remove the existing battery.
Wait for a Minute: Leave the clock without a battery for about a minute to allow any residual charge to dissipate.
Insert a New Battery: Insert a fresh battery into the compartment, ensuring the correct polarity (usually marked on the battery holder).
Start the Pendulum: Gently release the pendulum and let it start swinging.
Set the Time: Use the clock's time-setting knob or buttons to adjust the time to the correct hour and minute.
Your clock should now be restarted and keeping time accurately
4/3/2024 4:30:05 AM •
Home
•
Answered
on Apr 03, 2024
Not finding what you are looking for?