Boating - Page 2 - Recent Questions, Troubleshooting & Support


GO SEE YOUR LOCAL DEALER FOR ASSISTANCE

Boating | Answered on Nov 24, 2019


MEASURE IT AND GET SMARTER FOR YOURSELF

Boating | Answered on Nov 23, 2019


Do you have a question?
If you are looking for the journalist Verity Johnson, start with her website http://www.verityjohnson.com/ or a Google search.

Johnson Boating | Answered on Nov 19, 2019


See this. At about 4 minutes, he shows where the bypass screw is located. The fuse could be an inline one and is probably located by the control switch for the tilt unit, but it may be located somewhere else, depends on who wired it up.

Johnson Boating | Answered on Nov 04, 2019


  • Anonymous Oct 30, 2019https://www.manualslib.com/manual/824998...
    Not sure if this helps.

  • Anonymous Nov 02, 2019
    Valve Clearance Specifications
    For motors 70-horsepower and above, set the intake at 0.005 mm and exhaust at 0.006 mm.

Johnson Boating | Answered on Nov 02, 2019


Try this link to the manual for your boat and look under troubleshooting:
https://www.manualslib.com/manual/1073271/Carver-Yachts-36-Sedan.html

Carver Boating | Answered on Nov 01, 2019


I think there is a nut holding the prop to the shaft and there might be a shear pin going through the prop and shaft. Remove those to get the prop off. It may have been on so long, there might be rust and other junk holding it on. Spray with penetrating oil and let sit to loosen the rust.

Boating | Answered on Oct 31, 2019


I suggest you post your question on this forum:

http://www.boatered.com/forum/topic.asp?TOPIC_ID=131726

Boating | Answered on Oct 30, 2019


I suggest you go to this site and obtain a manual for your Evinrude engine. Hope it helps:

Literature

Boating | Answered on Oct 30, 2019


In demo mode, it will show fish and bottom details when the transponder is out of water. If the boat is in a mooring, put a metal spade under the transponder, you should see the detail change.

Google

make model manual

Boating | Answered on Oct 28, 2019


https://www.lowrance.com/en-au/help--support/fishreveal-software-upgrade/
It wont hurt to update any software,
Hope it works out,
cheers.

Boating | Answered on Oct 27, 2019


Sounds like one of the pins on the cable from your transducer is bent where it plugs into the back of the unit. check that first, then ensure the plug is all the way in. If it's not that, it's possible a wire is broken in the cable. You could try the wiggle test. With the unit on, have someone watch the screen and wiggle the wire that you can reach working from one end to the other. if the screen flashes or changes while you do this in a certain spot, there's your problem. This kind of problem usually comes from the wire being tight where it goes around a corner. Heat and vibration will finish the job

Boating | Answered on Oct 26, 2019


Try the following.
Ensure the connector going to the controller is secure.

Remove power to the motor by stowing it. Wait until the remote screen goes blank. Deploy the motor to power it up verifying that the System Ready light comes back on when the motor is deployed.
Press any button on the remote to turn it on.
If F code returns then probably controller board will need replaced.

Boating | Answered on Oct 26, 2019

Not finding what you are looking for?
Boating Logo

17,742 questions posted

Ask a Question

Usually answered in minutes!

Top Boating Experts

ray gallant

Level 3 Expert

66120 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

30360 Answers

Tom Chichester

Level 3 Expert

55370 Answers

Are you a Boating Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...