Garden - Page 5 - Popular Questions, Answers, Tips & Manuals
Chainsaw chain rotates when starter pulley is pulled, why?
20" is long for a saw that size but that in itself didn't cause the issue. What matters is proper chain pitch/gauge and length (link count). According to the manual it's 3/8 pitch .050 gauge chain and by extrapolating link count, it should be 68. But that's assuming original drive sprocket pitch/gauge.
Remove the bar and chain. The clutch/sprocket should spin freely. Check the bar didn't make contact with the sprocket which would imply the chain tension wasn't maintained.
11/13/2023 7:49:33 PM •
Garden
•
60 views • 1 helpful votes
Why won't my pressure washer pressure up?
Filtrul sau sita: Verific? dac? filtrul sau sita de la intrarea apei ?n ma?ina de sp?lat cu presiune este curat?. Dac? este ?nfundat?, poate restric?iona fluxul de ap? ?i, implicit, sc?dea presiunea.
Duza: Duza de pulverizare ar putea fi blocat? sau deteriorat?. ?n cazul ?n care este astfel, cur??? sau ?nlocuie?te duza.
Conexiunile sau furtunurile: Verific? dac? nu exist? scurgeri sau fisuri ?n conexiuni sau furtunuri. Pierderea de presiune poate ap?rea dac? exist? o problem? ?n sistemul de alimentare cu ap?.
Pompa: Pompa de ap? poate avea o problem? sau nu func?iona la capacitate maxim?. Verific? starea pompei ?i cur??? eventualele resturi.
Reglajele presiunii: Unele ma?ini de sp?lat cu presiune au reglaje de presiune care ar putea s? fie setate la un nivel sc?zut. Asigur?-te c? aceste reglaje sunt corecte.
Probleme electrice sau mecanice: Dac? exist? probleme electrice sau mecanice cu motorul ma?inii de sp?lat cu presiune, acestea ar putea afecta performan?a ?i presiunea.
Dac? problema persist? ?i nu po?i rezolva singur, ar fi indicat s? consul?i manualul ma?inii de sp?lat cu presiune sau s? contactezi un specialist ?n repara?ii pentru asisten??.
12/3/2023 4:20:21 PM •
Garden
•
35 views • 0 helpful votes
Karcher K2 Compact - Motor permanently running/no pressure
It sounds like there may be a potential issue with the pressure build-up mechanism in your Karcher K2 compact. The constant motor running without water pressure could indicate a problem with the pump or the pressure switch. I would recommend checking the following:
1. Check the inlet filter: Ensure that the inlet filter is clean and free from any debris or blockages. A clogged filter can restrict water flow and affect pressure.
2. Inspect the nozzle: Make sure the nozzle is not obstructed or damaged. A blocked or damaged nozzle can restrict water flow and affect pressure as well.
3. Check the pressure switch: The pressure switch is responsible for regulating the motor and water flow. It's possible that the switch is faulty or not functioning correctly. Consider contacting Karcher customer support or a professional technician for assistance with checking and possibly replacing the pressure switch.
4. Examine the pump: There might be an issue with the pump itself. It could be worn out, clogged, or experiencing other internal problems. In such cases, it's best to reach out to Karcher customer support or a professional technician for further diagnosis and repair.
Remember to always follow safety precautions and consult the user manual provided by Karcher for specific troubleshooting steps and guidelines.
How to remove broken bit in a WORX 176L
pull locking sleeve back as shown on page 3 of instructions. pick up a can of PB blaster dry lube spray can at HD and spray some around bir.
https://www.manua.ls/worx/wx176l/manual?p=3
11/30/2023 10:27:41 PM •
Worx Garden
•
33 views • 0 helpful votes
Won't crank over, quit in middle of mowing
If your mower won't crank over and quit in the middle of mowing, there could be several possible reasons for this issue. Here are some common troubleshooting steps you can take:
- Check the Fuel Level: Ensure that there is enough fuel in the mower's tank. If the fuel level is low, it might not have enough fuel to run.
- Inspect the Spark Plug: A fouled or damaged spark plug can prevent the engine from starting. Remove the spark plug and inspect it for signs of fouling, such as deposits or a worn electrode. Replace the spark plug if necessary.
- Fuel Quality: Make sure you are using fresh, clean fuel. Old or contaminated fuel can cause starting problems. Drain the fuel tank and replace it with fresh fuel if needed.
- Air Filter: Check the air filter for dirt and debris. A clogged air filter can restrict airflow to the engine, affecting its performance. Clean or replace the air filter as needed.
- Check for Obstructions: Inspect the mower deck and the blades for any obstructions or debris that could be preventing the blades from turning freely.
- Safety Switches: Most mowers have safety switches that prevent the engine from starting if certain conditions are not met (e.g., the blade engagement lever is engaged, the seat is not occupied). Check these safety switches to ensure they are functioning correctly.
- Battery: If your mower has a battery, check its charge. If the battery is low or dead, it might not provide enough power to crank the engine. Charge or replace the battery as necessary.
- Ignition System: Inspect the ignition system, including the ignition coil, for any visible issues. If there are problems, such as damaged wires or connections, they may need to be repaired or replaced.
- Fuel System Issues: Problems with the carburetor or fuel lines can also cause starting issues. Inspect the fuel system for any clogs, leaks, or other issues.
- Examine the Oil Level: Ensure that the oil level is within the recommended range. Low oil levels can lead to engine damage and difficulty starting.
If you've gone through these steps and the problem persists, it may be best to consult the mower's manual or seek the assistance of a professional mechanic to diagnose and address the issue.
11/19/2023 8:36:10 PM •
Garden
•
41 views • 1 helpful votes
Not finding what you are looking for?