Hello, friend! It is noteworthy that if the GE Spacemaker microwave model JVM240BL001 is displaying "Enter NORM SOUND 2" on the digital display, it indicates that the microwave is in the programming mode for adjusting the sound level. To exit this mode and return to normal operation, you can try the following steps:
Press the "Clear" or "Cancel" button. This should clear the programming mode and bring the microwave back to its normal state.
If pressing the "Clear" or "Cancel" button doesn't work, you can try unplugging the microwave from the power outlet for about a minute. Then plug it back in and see if it resets the display.
If the issue persists, consult the user manual for your specific model. The manual may provide additional instructions or troubleshooting steps to resolve the issue.
If the turntable spigot on your Hamilton Beach microwave has arced and burned even after cleaning it with a wire brush, it indicates a potential issue with the electrical connection or the turntable motor. Here are a few steps you can take to address the problem:
Disconnect Power: Before proceeding with any repairs, ensure that the microwave is completely disconnected from the power source to avoid any risk of electric shock.
Inspect the Turntable Spigot: Carefully examine the turntable spigot for any signs of damage, such as burn marks or melted plastic. If the spigot is severely damaged, it may need to be replaced. Contact Hamilton Beach customer support or a qualified technician to inquire about replacement parts and proper installation.
Check the Wiring: Inspect the wiring connections near the turntable motor for any loose, frayed, or damaged wires. If you notice any issues, they should be repaired or replaced by a professional technician to ensure safe operation.
Test the Turntable Motor: The turntable motor may be faulty and causing the arcing issue. To test the motor, you will need a multimeter to check for continuity and proper functioning. However, this requires electrical knowledge and experience, so it's best to consult a qualified technician for assistance.
Seek Professional Assistance: If the arcing issue persists after performing the above steps, it is recommended to contact Hamilton Beach customer support or a professional technician. They will have the expertise to diagnose the problem accurately and perform any necessary repairs or replacements.
The filter might need to be replaced. For the manual I would try searching on the companies official website to see if they have a manual for your microwave.
The thermal fuses and the ceramic fuse might of had blown and need to be replaced. It could also be that door switch and the door latch are not working. The plug could be bad.
Wine coolers can stop cooling for six common reasons - A break in electricity, compressor problems, capacitor problems, the condenser fan stops working, a defective thermostat, or a broken evaporator. Most of these problems can be troubleshot at home, but a technician is needed for advanced issues.
If your Lamona electric oven is stuck in demo mode and the manual does not provide any information on how to disable it, you may try the following steps:
Unplug the oven from the power outlet for a few minutes and then plug it back in. This may reset the oven and remove the demo mode.
Press and hold the "-" button for about 10 seconds. This may disable the demo mode and activate the oven.
If the above steps do not work, try pressing and holding the "Function" button for about 5 seconds. This may activate or deactivate the demo mode.
If none of the above steps work, contact the manufacturer or a professional technician for assistance.
Try a power disconnect at the plug socket for 5 minutes. If that doesn't reset it, you will need a local repairer. The most likely reason is a door safety micro-switch has failed or moved out of adjustment. There are normally three on the door and hinges to prevent operation with an open door.
https://www.fixya.com/support/r29874712-repairing_microwave_ovens
..
Consumer fuses are normally on the rear where the power lead goes in. It is a small screw cap or a long pull out fuse with a small notch in the end. If there is an internal fuse, it will be on the main circuit board. Getting inside is normally not easy because of security screws.
https://www.fixya.com/support/r29874712-repairing_microwave_ovens
..
A "FAIL" code on a Galanz microwave typically indicates a problem with the electronic control board. This can be caused by a variety of issues, including a malfunctioning sensor, a software error, or a problem with the power supply.
It's recommend you to unplug the microwave for a few minutes and then plug it back in. If the problem persists, you should have the microwave checked by a professional technician.
You can also try to reset your microwave by following the steps in the user manual, which typically involves pressing a certain combination of buttons on the control panel.
If the problem is still there, it is advisable to contact the manufacturer or a professional technician for repair. This will help you to get a more accurate diagnosis and a solution to the problem. Depending on the cause of the issue, the cost of repair can vary.
the light is powered ab AC so any minuscule DC voltage may be meter error.
this vent hood is designed to use incandescent bulbs. call service center listed in you manual for more specific info. If you are concerned about safety return hood to place of purchase. You are the only one who knows how you wired it
It is a motorized drawer and I doubt it likes being opened manually. It would need to be repaired professionally due to the inherent dangers of microwave energy. The drawer motor would be operated by a relay.
Did you read any reviews before you purchased it?
IanFromOhio
a year ago
Thumbs Down
- Looks great but features are bad.
Drawer microwaves and this model in particular look great. We did a big reno in December and this is now in the island. Looks good and functions as a basic microwave. Everything else is just south of mediocre. I'd suggest you get a drawer microwave from another company. Bad Stuff: - door opens/closes very slowly (~4 seconds)... doing a 30 second reheat now takes 4+4+30+4+4 = 50% longer just standing around. Likely similar with other drawers, but an unexpected negative. - doesn't let you tell it to start until fully closed - its default sounds and reminders are ridiculously annoying - beep-beep-beep on finish, and 10 seconds after that, and 10 seconds after that, and.... on and on - it forgets all settings during a power outage, turning back on the annoying sounds - and forgets your network connection - but good news, you won't want to use that feature - controls are not intuitive - classic 40 buttons where you use 5 The WiFi & App - hilariously bad. Design in your head the things you would want in a microwave app. Sharp engineers designed the opposite. Can you set the alarm settings in the app? No. Do you get a notification each time the microwave finishes cooking? Yes. I guarantee you will delete the app within 48 hours. Hand Wave to open. Neat right? No. Take how long it takes for this thing to open/close and add another 4-8 seconds of waving your hands (which are full food, else you'd just press the button) to then wait for the drawer to open. Push to close works well, but it reacts in a weird way, so some concern I'm breaking it. I stopped doing wave to open after the first week and stopped trying to demonstrate it to friends after one month (cause it will make you look silly). Height - just tall enough - fits a Venti coffee Cooks at 950 watts - basically the same power as a college-dorm microwave Cost. my god, how much did I spend on this. The good: Looks good Flush install if you have a good installer; mine is shown in a 30" wide lower microwave cabinet by Medallion Reheat sensor cook works well push to close works. It was suggested that I buy a Sharp because they have the patent on the drawer microwave and everyone else is just a re-labelled Sharp. I would suggest you give the others a look. They may be using the same hardware, but hopefully they have a more customer-focused interface and better software engineers working for them.
Reviewed on bestbuy.com
