Hardware & Accessories - Page 6 - Recent Questions, Troubleshooting & Support
Have Intermatic EJ500 timer. Light comes on ok and when it goes off the bulb does not turn off completely. It just dims. Try to turn it off with on off by pressing on off but to no avail.
If the light on your Intermatic EJ500 timer is not turning off completely, it could be due to a faulty relay switch or a loose connection. Here are a few troubleshooting steps you can try:
- Reset the timer: Turn off the power to the timer, wait for a few minutes, and then turn it back on. This will reset the timer and may fix any issues that were causing the light to stay on.
- Check the wiring: Make sure all the wiring connections are tight and secure. If any of the wires are loose, tighten them with a screwdriver.
- Replace the relay switch: If the relay switch is faulty, it may need to be replaced. You can purchase a replacement switch and follow the manufacturer's instructions for installation.
- Check the light bulb: Make sure the light bulb is the correct wattage and type for the timer. If the bulb is not compatible, it may cause the light to stay on even when the timer is turned off.
If these steps do not resolve the issue, it may be best to consult a professional electrician or contact Intermatic customer support for further assistance.
My Tork timer goes on and off at the set pin times, but then it comes on in the evening when it's not supposed to?
If your Tork timer is turning on at times when it's not supposed to, there may be a few potential causes. Here are some things to check:
- Check the programming: Make sure the timer is programmed correctly and that you have set the correct on/off times.
- Check for stray signals: If your Tork timer is receiving stray signals from other devices, this could cause it to turn on or off unexpectedly. Try moving the timer to a different location, away from other electronics.
- Check the power source: Make sure the timer is receiving a steady power source. If the power is interrupted or fluctuates, it could cause the timer to malfunction.
- Check for interference: Interference from other electronics, such as nearby radios or TVs, could be causing the timer to malfunction. Try moving the timer to a different location or turning off nearby electronics to see if this solves the problem.
If none of these solutions work, it's possible that there is a problem with the timer itself and it may need to be repaired or replaced.
I need an instruction mannual for the le saucier with the automatic dial
Le Saucier is a kitchen appliance that is used to make fresh butter and other creamy sauces. Without knowing the specific model of Le Saucier you have, it is difficult for me to provide an instruction manual for the automatic dial. However, here are some general instructions on how to use the Le Saucier:
- Assemble the Le Saucier according to the manufacturer's instructions. Typically, this involves attaching the paddle and placing the machine on a flat surface.
- Pour the cream into the Le Saucier. The amount of cream needed will vary depending on the size of the machine and the recipe you are following.
- Set the machine to the desired speed and let it run. The automatic dial may allow you to set a specific speed or program, depending on the model.
- After a few minutes, the cream will thicken and eventually turn into butter. Once the butter has formed, stop the machine and drain off any excess liquid.
- Use a butter churn or cheese cloth to remove any remaining liquid and shape the butter into a desired form.
If you are still having trouble with your Le Saucier or need a specific instruction manual, I recommend contacting the manufacturer or searching online for a downloadable manual.
Do you know where I can find a timer for a Westpoint DQP 12 set 9011
I'm sorry, but as an AI language model, I don't have access to information on specific product manuals or instructions. However, I can provide you with some general troubleshooting steps for a timer that is not working properly.
- Check the power source: Make sure the timer is properly plugged in or has a fresh battery if it's a battery-operated device.
- Check the settings: Verify that you have correctly set the timer for the designated time and that it is in the correct mode of operation.
- Reset the timer: If the timer is not working as intended, try resetting it to its default settings.
- Clean the timer: Dust and debris can affect the timer's functioning, so make sure to clean it thoroughly.
- Seek professional help: If none of the above steps work, it may be time to seek professional help or replace the timer.
If you are still having trouble finding a timer specifically for your Westpoint DQP 12 set 9011, I would recommend reaching out to the manufacturer or a professional technician for further assistance.
AMF Paragon TI Mite Timer - Model PLTI-O. How do you set the timer on it please?
Question edited for a lot more clarity.
Question moved from Office Equipment to Timers.
This timer has a fixed setting for turning on lights or appliances. To set the time, turn the small dial marked '8765' (which represent the hour when the lights will turn ON, so that the time you wish them to come on is next to the current time. In other words, if the current time is 6:00pm, and you want to have the lights come on at 8:00pm, set the 8 on the small dial next to the 6:00pm on the timer body, and plug everything in.
..
Would you please explain how to bypass the timer on a Smeg A2-2 Oven.
It is not recommended to bypass the timer on your Smeg A2-2 oven, as the timer is an important safety feature. However, if you still want to bypass the timer, here are the steps:
- Turn off the power to the oven at the main breaker.
- Locate the timer wires. In your case, there are 2 black pairs, 1 red pair, and a single white wire.
- Determine which wires are connected to the timer. These wires will be labeled "timer" or "clock."
- Cut the timer wires close to the timer unit.
- Strip the ends of the wires back about 1/2 inch.
- Twist together the wires that were previously connected to the timer.
- Cover the twisted wires with a wire nut.
- Wrap the wire nut and wires with electrical tape.
- Turn the power back on and test the oven.
Again, it is not recommended to bypass the timer on your oven, as this can be dangerous and may void your warranty. It is recommended to consult a professional technician or the manufacturer before attempting any repairs or modifications to your oven.
Hurcon vx salt chlorinator timer cannot be set to start beyond 19 hrs
The Hurcon VX salt chlorinator timer should allow you to set the timer beyond 19 hours (7pm). If you are unable to set the timer beyond this point, it may indicate a problem with the timer or the programming.
Here are some troubleshooting steps you can try to resolve the issue:
- Reset the timer: First, try resetting the timer by turning it off and unplugging it from the power source for a few minutes. Then, plug it back in and try to set the timer again.
- Check the programming instructions: Make sure you are following the correct programming instructions for the Hurcon VX salt chlorinator. Consult the user manual or manufacturer's website for detailed programming instructions.
- Check the timer mode: Check that the timer is set to the correct mode, such as 24-hour time mode or 12-hour time mode.
- Check the wiring: Check the wiring connections to ensure they are properly connected and not loose or damaged.
- Contact the manufacturer: If none of the above steps resolve the issue, contact the manufacturer or a qualified technician for further assistance. It is possible that there may be a problem with the timer itself that requires repair or replacement.
How to set timer to operate properly
To set your Garrison timer model 52-8817-6 to operate properly, you may need to adjust the time and the mode settings. Here are the steps you can follow:
- First, set the correct time on the timer. To do this, locate the "TIME" button and hold it down until the hour digits start to flash. Use the "+" and "-" buttons to adjust the hour, then press the "TIME" button again to move to the minute digits. Repeat the same process to set the correct minutes.
- Once you have set the correct time, you can then set the mode. To do this, locate the "MODE" button and press it until the desired mode is displayed. In your case, you will want to set the timer to the "PM" mode.
- Finally, set the on and off times for your device. To do this, locate the "PROG" button and press it to enter programming mode. Use the "+" and "-" buttons to set the on and off times for each day of the week.
If you have followed these steps and your timer is still not operating properly, you may need to consult the user manual or contact the manufacturer for further assistance.
Can I reuse the rear spinal nut on my 2000 ford focus ?
It is generally not recommended to reuse a critical fastener like the rear spinal nut on your 2000 Ford Focus. These nuts are designed to provide a precise amount of clamping force and ensure proper alignment of the rear suspension, so reusing them may compromise the safety and performance of your vehicle.
Wiring diagram for Mastercraft RT550B rotary tool
The black line wire connects to the negative (-) terminal on the circuit board. You may find wiring diagrams for specific products online, or you can reach out to the manufacturer for detailed instructions.
Not finding what you are looking for?