Freezers - Page 4 - Answered Questions & Fixed Issues

Yes, it is safe to leave an Igloo ice machine when it is full. However, if you plan to leave the ice in the machine for an extended period, it is recommended to transfer the ice to a freezer to prevent melting and refreezing, which can cause the ice to clump together.

If your Frigidaire chest freezer is not turning on after a short move and the light is not even coming on, there may be a few things that could be causing this issue:

1. Check the power source: Make sure that the freezer is properly plugged in and the outlet is receiving power. You can try plugging another device into the same outlet to confirm if it's working or not.
2. Check the power cord: Check to see if the power cord is damaged or frayed. If it is, it may need to be replaced.
3. Check the control board: There may be an issue with the control board of the freezer. Try unplugging the freezer for a few minutes and then plugging it back in. This can sometimes reset the control board.
4. Check the compressor: If the compressor is not functioning properly, the freezer will not cool. You may need to contact a professional to repair or replace the compressor.

If none of these solutions work, it may be best to contact a professional to diagnose and fix the issue.

If your igloo model frw062 has stopped cooling, there are a few possible reasons why this might be happening:

1. The temperature control could be malfunctioning: If the temperature control is not working properly, it could be causing the refrigerator to run continuously and not cool properly.
2. The condenser coils could be dirty: Over time, the condenser coils can become dirty, which can cause them to overheat and reduce the cooling efficiency of the refrigerator.
3. The compressor could be failing: The compressor is responsible for compressing the refrigerant and pumping it through the system. If the compressor is failing, it may not be able to do its job effectively, which could result in poor cooling performance.
4. The refrigerant could be leaking: If the refrigerant is leaking from the system, the refrigerator will not be able to cool properly.

To fix the issue, you may need to troubleshoot the refrigerator and try to determine the cause of the problem. If you are unable to identify the issue, it may be best to contact a professional for assistance.

If the alarm light on your AEG freezer is still flashing after you have followed the instructions and pressed the button, it may indicate a problem with the freezer. You can try unplugging the freezer and leaving it unplugged for a few minutes, then plugging it back in to see if the alarm light resets. If the alarm light continues to flash, you may need to consult the manual or contact AEG customer service for further assistance.

A flashing red light on a tall freezer indicates that the appliance has detected a temperature alarm, and the temperature inside the freezer has likely dropped below the desired range. A temperature of -6 degrees Celsius is much lower than the recommended temperature for a freezer (-18 degrees Celsius), which can cause frozen food to become damaged or spoiled. To resolve the issue, you should first check the freezer's manual for troubleshooting tips and recommended actions. In general, you may need to adjust the thermostat to a higher temperature, remove any obstructions to airflow, or defrost the freezer if ice buildup is blocking the evaporator coils. If the issue persists, you should contact a qualified technician to diagnose and repair the freezer.

The SUPER button on a Skandiluxe chest freezer is typically used when you need to freeze food quickly, such as when you've just added a large amount of unfrozen food to the freezer. The SUPER function causes the freezer to operate at its coldest temperature for a period of time, which helps to freeze the food more quickly. After the desired amount of time, you can turn off the SUPER function to return the freezer to its normal operating mode.

A loud noise when turning on an Igloo portable ice maker could indicate a problem with the compressor or a malfunctioning fan. It is recommended to unplug the appliance and have it inspected and repaired by a qualified technician.

The defrost timer in a Westinghouse fj383 freezer is typically located at the back of the unit, near the compressor. It may be behind a cover or housing that needs to be removed in order to access the timer. If you're unsure about locating the defrost timer or don't feel comfortable working on your freezer, it's best to consult the user manual or contact a professional technician for assistance.

If the ice machine runs for a while and then gives a water error despite the water pump working and there being plenty of water, it's possible that there's an issue with the water level sensor or control board. It may be necessary to have a professional technician diagnose and repair the machine.

The location of the 9V battery on a Kenmore upright freezer model 970 can vary depending on the specific model and design. However, in general, the 9V battery is typically located in the control panel or on the back of the freezer near the compressor. You may need to consult the freezer's manual or contact Kenmore customer support for more specific information regarding your model.

If the Hoshizaki F-450maf ice machine's reservoir tank has no water, you should first check that the machine is properly connected to a water supply and that the water supply valve is turned on. You should also check that the machine's water filter is clean and not clogged. Additionally, make sure that the float switch is functioning properly and that it is not stuck in the "off" position. If these steps do not resolve the issue, you may need to consult the machine's manual or contact a professional for further assistance.

The Kelvinator FD830 upright freezer has three temperature indicator lights located on the top right outside corner to show the current temperature range inside the freezer. The green light indicates that the temperature is within the safe operating range, while the yellow light indicates that the temperature is rising and nearing the upper limit. The red light indicates that the temperature has exceeded the safe operating range and may lead to food spoilage.

To get the green power light to come on for a Brada mf 183 upright freezer, you should first make sure that the freezer is plugged in and that the outlet is functioning properly. If the outlet is working correctly, try resetting the freezer by unplugging it for several minutes and then plugging it back in. If the fast freeze light is still on, it may indicate an issue with the temperature control or sensor, and it may be necessary to contact a professional for repair or replacement.

To access the No-Frost System located on top of your Miele tall freezer F7462 SNH-1, follow these steps:

1. Unplug the freezer and remove all items from the freezer compartment.
2. Locate the air grille on the top of the freezer.
3. Remove the air grille by pulling it upwards from the front edge.
4. You should now be able to see the No-Frost System behind the air grille.
5. Use a soft-bristled brush or a vacuum cleaner to remove any dust or debris from the No-Frost System.
6. Once you have finished cleaning, replace the air grille by pushing it back into place.

Note: If you are not comfortable accessing the No-Frost System on your own, it is recommended to consult the Miele customer service or a professional technician for assistance.

The error code -H9 on a Frigidaire upright freezer typically indicates a communication error between the control board and the display board. To troubleshoot this issue, try unplugging the freezer for a few minutes, then plugging it back in to see if the error code clears. If the error persists, it may be necessary to replace one or both of the boards. Contact a qualified appliance repair technician for further assistance.

If your Whirlpool upright freezer is working fine but an intermittent alarm is sounding that is different from the high temperature alarm, it could indicate an issue with the door or the door switch. The alarm is designed to alert you if the door has been left open for an extended period or if the door switch is malfunctioning. Check the door seal to ensure it is tight and the door is closing properly. You can also try cleaning the door switch to see if that resolves the issue. If the problem persists, it may be necessary to contact a professional for further assistance.

Perhaps the power outage, was caused by your freezer? When you think a reset would help, the run light should come on, after a little while. But perhaps only the thermostat is defect. Be aware there can be so many causes, and none has to be related to the power outage, for your freezer not to work. It would be virtually impossible to see what is wrong, from a distance. Better try to bring the food to a working fridge and call a tech to solve the problem.

Question edited for typo. Question moved from Washing Machines Category. Please don't type in all CAPS, it is considered SHOUTING and rude, plus harder to read. You have a dead short to earth. Strip off all the panels and look for water where it shouldn't be and chaffed cables especially near holes in the casing. If you can't find anything, you need to check individual items, compressor, pump, and grinder with a multimeter. Or just call for service.

The fix is to replace ther faulty cpmponent. To do that, one must fault find the item with a multimeter, basic tools and electrical knowledge.

no info generic answer most likely can be fixed ust need to find out what problem is --was one of the electricial components damaged --wire disconnected etc