Cameras - Page 4 - Recent Questions, Troubleshooting & Support

Question edited for clarity and add maker. The batteries are shot, under powered and you need new ones. The orange flashing lights are the clue. also make sure the battery contacts are clean and bright. ..

Question translated into written English, add CAPS, fix typos and remove text speak abbreviations. Question moved to Model Category. Try this reset fix.

I have a Kodak Easy Share C513. The flash doesn't work

JustAnswer https://www.justanswer.com > Camera Problems Dec 28, 2012 - 1. Remove the battery and memory card from the camera. ... for approximately 20 minutes. 3. Reinstall the battery and power on the camera and let ... 1 answer · Top answer: It is not minor problem.If it is not under warranty then please don't send it to service ... Missing: m853 ‎' Show results with: m853

I have a kodak easyshare m753 the flash wont work

Fixya https://www.fixya.com > support > t3124129-kodak_e... Jul 15, 2009 - Remove your battery and memory card for 15 min and put them again. (you can also try by putting new batteries. In some cases battery can be ... Or camera repair near you. https://www.google.com/search?q=kodak+digital+camera+repair+near+me .

On Nikon cameras this isn't normally an error code. Have you got a memory card in the camera? Check that it isn't nearly full. r07 common comes up as an information prompt referring to the memory space in the camera. '07' being 7 shots remaining. If the card isn't full try this. Turn the camera off. Remove the battery. Remove the memory card. Leave it like that for at least 15 minutes. Connect the memory card to a computer or a laptop and check you can still look at and move the images that are on there. This is to check the memory card isn't corrupted (developed a fault).

Normal people can't fix electronic cameras, you need to be an electronics engineer and an optical engineer. Take to a Camera Service Centre for evaluation and repair.

That depends on what the system is.

• The "r07" message on a Nikon camera typically indicates the number of available shots in the camera buffer. It's not an error but rather an informational message. The number "r07" means that there are seven shots available in the camera buffer before it fills up. This is a normal part of the camera's operation and doesn't necessarily indicate a problem. It's more noticeable when you're shooting in continuous or burst mode. If you experience issues beyond this, it's advisable to check your camera settings and consult the camera manual. https://caranddriver.com/

it will not fit, but rather than ask why did you not just try it.

I believe you are looking for a USB transfer cable for your Sony Cybershot N50. I found a replacement USB camera transfer data sync charging cable cord for Sony Cybershot Cyber-Shot DSCH200, DSCH300, DSCW370, DSCW800, DSCW830, DSC-H200, DSC-H300, DSC-W370, DSC-W800, DSC-W830 digital camera on Amazon . This cable is compatible with several Sony Cybershot models, including the N50. The cable is priced at $7.95 and comes with a 30-day return policy. Amazon.com: Replacement USB Camera Transfer Data Sync Charging Cable Cord for Sony Cybershot Cyber-Shot DSCH200, DSCH300,DSCW370,DSCW800,DSCW830,DSC-H200,DSC-H300,DSC-W370,DSC-W800,DSC-W830 Digital Camera (Black) : Electronics

Question edited for clarity. Question moved from Cars and Trucks category. Question translated to English. We only speak English on Fixya. New Button board needed. https://www.google.com/search?q=nikon+coolpix+s2500+repair ..

JHJJ,JG.KFDL

If your Canon AV-1 is only shooting in Bulb (B) mode, it could be due to a malfunctioning shutter or aperture control. However, since the light meter is working correctly, it is possible that the issue is with the camera's shutter speed dial. The shutter speed dial is located on the top of the camera and should be set to a specific speed when shooting in aperture-priority mode. If the dial is stuck in the Bulb (B) position, then the camera will only shoot in bulb mode. I would recommend taking your camera to a professional camera repair shop to have it inspected and repaired if necessary.

Greetings jayantbhalla,

Unfortunately we do not offer international shipping at this time. One solution I have recommended before was to have an item shipped to a friend or relative in the states and have them send to you.

I hope this helps.

Thank you,

Agent Dort.
Go Ahead. Use Us.

If you included make, model and age, that may help you get an answer.

I'm assuming by "shutter" you're referring to the one inside the camera and not the cover blades on the very front of the lens. How old is the battery and do you use the camera a lot? Old batteries can be fully charged but can become weak and not hold that charge when the camera is powered on. The shutter issue could be part of this as the battery might not be strong enough to power the shutter. I think the batteries for these cameras are reasonably cheap so you could invest in a new one to see if that helps. An extra battery is always useful if you use the camera a lot. If this is an old, well used camera part do wear out so if new battery doesn't help you may need to take it to a good repairer as the camera will need to be taken apart to find the problem.

you will find a buyers address and a delivery address on the order form fill it out correctly and it will be delivered to that address

It was answered here. You asked for a manual and you were given 2 answers although one appears incorrect.https://www.fixya.com/support/t29944178-free_manual_gsc35_50ir_get_inside_screenTry herehttps://www.google.com/search?q=Hunten+Outdoors+Field+camera..

Hello

The problem is that the lens has become stuck in the barrel. There are some DIY solutions you could try, but the probability is that you will have to get it fixed by a professional.

Use these at own risk as it may further damage the camera.

Firstly , try connecting your ac adapter or usb cable.

Try holding the shutter button while switching on the camera.

Look at the lens , and if some of the lens 'circles' is misaligned or not concentric then try wiggling it (while holding camera lens down).

Try gently pushing or pulling the lens when it extends but this is risky as it may cause the lens barrel to slip out of its guidance system.

Another way to do this is to place the camera lens down on a hard surface and then power it up. Be sure to use a soft cloth or something similar as to not scratch your lens or casing. Let the lens push the camera up and down a few times and sometimes the little resistance provided by the camera is enough to get things going again.

Try hitting your camera near the lens on the body with the soft tissue on the palm of your hand.

Other than that , I would take the camera to a repair center for a evaluation to see if it would cost more to repair than to replace the camera.

If it is still under warranty I would suggest you take it in before trying any of these steps and remove any off-brand batteries or accessories as some stores are really fussy about warranty repairs on camera's with non-brand accessories.

You can also have a look at THIS link.

Hope the advise is useful. please do not hesitate to let me know if you need any further assistance. Also, please be so kind to let me know if you found this helpful.

Regards
Andrea

Please get it here : www.opendrivers.com/.../concord-free-driver-download.html
www.driversupdate.org/concord-camera.htm

Regards