Crafts & Hobbies - Page 2 - Recent Questions, Troubleshooting & Support

jus look in the manel thankks DING

You would have to know how much 1 cubic inch of candle wax weighs to convert size to weight.

replaced printer controller board or cable along printer controller to CPU board

We are FIXYA dot com, we don't repair anything. We only supply information. We are not who you think we are. Click the link to find repair shops near you. https://www.google.com/search?q=knitting+machine+repairs+near+me ..

https://www.google.com/search?q=Wiring+diagram+for+a+minitronics+RU1-1+auto+reverser ..

moved this post to toy trains.TOY TRAIN "This is an HO scale electric train, the fault is in the bachmann brand EZ COMMAND control"

I can help you find the parts you need for the Lionel 1987 Electric Gold Rush Special 0-6-0 Locomotive. The parts you need are bushings for the wheels. I recommend looking at hobby train parts suppliers such as Lionel Trains, Trainz, and Model Railroader for the bushings.

Question edited for clarity and add maker. Question moved from Staples Business Depot to model category. The 5700 has a Lifetime Warranty for as long as you own it. They will repair or replace. https://arrowfastener.com/tool/t50/arrow-fastener-manual-stapler-warranty/ https://arrowfastener.com/tool/5700/ ..

Question edited for a lot more clarity based on the little information provided. All question need full 'make model (what it is)' please.Question moved from Saws to a Grizzly 20" Planer.In the link, but it seems discontinued. You may have to use two blades together or have them made.https://www.google.com/search?q=Grizzly+H2255+planer+blades..

• Turn on the machine, with no cartridge installed. Roll the Speed, Size and Pressure dials all the way down to the lowest possible setting on each.
• Grab the blade assembly with two fingers and pull the carriage gently all the way to the left. Behind where the carriage usually sits is a red button. Press and hold the button for three to five seconds and release.
• Go back to the three dials marked Speed, Size and Pressure, and roll each one all the way up and down three or four times.
• Press the Cut button, then turn off the machine. Let the machine sit for 15 to 20 minutes to clear the memory.
• Load a cartridge, turn the machine back on and try it out. If you are still experiencing problems, you may have a defective machine. Return it to the manufacturer with the original receipt.

There are no free ones. https://ozarktoolmanuals.com/machinemanual/delta-rockwell-dc-33-13x5-9-wood-planer-operator-part-manual/ Mike's Tools has other models https://www.mikestools.com/Delta_Planer_Owners_Manuals.aspx ..

Hi, Please make sure that the wireless controlloer power switch is set to "on." Please also give the train a new command. If it does not start to run, either your engine or remote need repair and you would need to reach out to Lionel by calling 1 (586) 949-4100. Thank you.

Google. Less than 2 Seconds it took. https://www.google.com/search?client=firefox-b-d&q=aleene%27s+ultimate+glue+gun+manual

Depends what you mean by small hills? Has the loco climbed these small hills in the past without problem? A one in twelve (one inch climb for every twelve inches travelled) incline is about as much as this loco could manage I imagine, and even less when loaded with box cars etc. Sadly the traction drive on these loco's seems to have a short life. I have heard that giving the loco a good firm solid whack down onto a hard surface may get the internal gears to settle down and get more traction. There's an average chance it might work. Do not attempt to open it up, this will create a real mess because it's just about impossible to get all the minute loaded springs back into their correct place.

I had an issue with these before, put a dime under the front middle of the base, it should fix it, if its the same problem i had. can you tilt it and will it work? sometimes when the base is not flush this tends to happen.

Call the Toll Free phone number on the unit and give them the model and serial number. They can help you.

You need moisture control if laying below ground level or on concrete anywhere as concrete is porous

there is probably something wrong with the computer and the machine may need to be serviced

ask maker yet, ?