Plumbing - Answered Questions & Fixed Issues


You might try to Isolate cause by exchanging faucet head (sensor) with one of the other units.

Suggest using a "DC" capable current probe to observe battery drain and compare good and bad units. See following probe;

https://www.lowes.com/pd/Southwire-Digital-600-Volt-Truerms-Ac-Dc-Clamp-Meter/1001002506

With the probe you'll be able to determine results immediately instead of waiting 2 weeks for pass/fail.

Comment here for further assistance.

Toto Plumbing | Answered 2 days ago | 14 views


normally, they are screwed on. so if the threads are damaged, it will be loose and will need replacing

Plumbing | Answered on Jan 06, 2020 | 16 views


Might be your filter jamed so you can test with clean the filter. My website - Cleck Hare

Plumbing | Answered on Dec 26, 2019 | 34 views


If a replacement switch is available and you know how to replace it

Plumbing | Answered on Dec 24, 2019 | 180 views


try turning off water supply then open all faucets to let then bleed down then close them and turn water back on should be ok

Delta Plumbing | Answered on Dec 24, 2019 | 25 views


The cartridge has a leaking o-ring or is faulty. Replace the cartridge under warranty and grease it up with Water Pump Grease when you refit it.

Plumbing | Answered on Dec 22, 2019 | 21 views


Can you tell us more about what you mean by Disable?

If you mean,how can you stop water from flowing, there are usually shutoff valves in the hot and cold water supply lines under your sink (nothing to do with the faucet itself).

Plumbing | Answered on Nov 18, 2019 | 31 views


Need more information make of faucets so forth

Plumbing | Answered on Nov 14, 2019 | 30 views


Download the BILT app and search for your faucet model. The icon is turquoise with a white nut ( as in nut and bolt).
It will show you step by step nearly everything under the sun. Hope that helps a bit.

American... | Answered on Nov 09, 2019 | 45 views


Its probbably the hose connected to the valve, try screwing it back on and turn the water up slowly, if that does not help, check your local radio shack

Maax Brio II... | Answered on Nov 06, 2019 | 2,557 views


THEN CALL A PLUMBER TO REPLACE IT

Kohler Plumbing | Answered on Nov 06, 2019 | 34 views


First clean out your cabinets under the sink. Second turn turn the cold water valve off, hot water valve as well.
You should be able to locate the sprayer hose as it will have a weight on it, this helps to pull the sprayer back when you are finished with it. Remove the weight by lifting up on the tab should be on the center of the weight.
Then you should see the hose connection.There you should see a button.Push it in and give it a little tug. The hose should be disconnected. Just follow in reverse order to reinstall.
I hope this is information is helpful. Have a blessed day.

Moen Plumbing | Answered on Nov 06, 2019 | 35 views


Leaking from the stem or handle 90% of the time means all you need is a new cartridge or new O rings or seals, depending on the model of your faucet.
Phister has a warranty https://www.pfisterfaucets.com/parts-support/warranty-information
and if they are like other faucet manufacturers with a similar warranty, just take the bad part(s) to your local authorized Pfister dealer and they will exchange them over the counter. Otherwise, you can contact Pfister through their website.

Plumbing | Answered on Oct 30, 2019 | 39 views


There are a lot of variables. Are you on a shallow well pump? It sounds like the well doesn't make much water. Check your well tank pressure. With 0 psi of water (drain the pressure) There should be 2 psi of air less than than the start up. If the pump is set to start at 30 psi, there should be 28 psi of air in the tank. It sounds to me like either the tank is shot, or the pump doesn't make much water. If you leave a faucet on while putting air in the tank and air comes out the faucet, then, the bladder is shot.

Plumbing | Answered on Oct 30, 2019 | 249 views


That pump doesn't have a pressure switch! It has a digital flow sensor on discharge. It will keep running so long as there is a flow. Usually caused by dripping tap, or leak. Pressure doesn't stop the pump. By the way - Don't expect to get parts from Canadian Tire or Mastercraft - They told me that they carry NO parts for that pump. It is very similar to a Burcam pump and they may have parts or offer service.

Plumbing | Answered on Oct 17, 2019 | 173 views

Not finding what you are looking for?
Plumbing Logo

Ask a Question

Usually answered in minutes!

Top Plumbing Experts

Brad Brown

Level 3 Expert

18136 Answers

Tom Chichester

Level 3 Expert

55370 Answers

Gil Shultz

Level 3 Expert

3388 Answers

Are you a Plumbing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...