Plumbing - Page 5 - Recent Questions, Troubleshooting & Support


Sounds like the nut attaching faucet under sink has loosened. You have to crawl under sink to tighten it.

Plumbing | Answered on Aug 06, 2019


Take a set and go from larger to smaller until one fits.

Moen Plumbing | Answered on Aug 06, 2019


Sizes differ. Take a set and go from larger to smaller until one fits.

Plumbing | Answered on Aug 06, 2019


You have just published your contact details to the 11 million viewers of Fixya. I have removed them. I have also moved your question from the Cellphones category.

Call your local Northstar technician which can be found in this link.

https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&ei=pWJEXbn4IYratAWV2LCQCQ&q=northstar+water+conditioner+service

Northstar... | Answered on Aug 02, 2019


I need 300 2go credit in my 2go account

American... | Answered on Jul 23, 2019


If your pool pump is acting sluggish it may simply be a build up of debris inside the impeller. Cleaning it is simple if you know how.
Step 1 - Check the Impeller

You can check the impeller for clogs by opening the clear cover that is on the strainer basket. Then place your garden hose into the basket and turn it on high. The water should disappear immediately. If it does not, you may have a clog.
Step 2 - Turn off the Power to the Pump

Before actually removing the clog from your pool pump impeller you will need to turn off the power to it. Remove the basket and use a finger to reach into the hole behind the basket to feel for any debris. If it is clogged, go to step 3.
Step 3 - Disconnect the Pump and Motor

Disconnect the pump and motor from the plumbing. Depending upon the make and model of your pool pump you may be able to skip this step. The motor usually just slides away from the pump.
Step 4 - Remove the Plastic Cover

Take the pump apart by removing the plastic cover over the motor. This cover generally has several small screws holding it on.
Step 5 - Remove and Clean the Impeller

Once the cover is removed you will easily be able to see the clog in the pool pump impeller. Just use your fingers or a coat hanger to clean it out.
Step 6 - Clean

Put everything back together. Once you have it cleaned out you can put the cover back on and put it all back together. Problem solved.

Plumbing | Answered on Jul 18, 2019


Once you take off the front cover. You will see the impeller. Take of the rear cover and the shaft has a flat spot on it. You can hold it with a open ended wrench and spin off the impeller. It will be tight. There is no need to take it off unless it's broken.

Goulds Pumps... | Answered on Jul 18, 2019


If by double you mean separated levers, there will be a nut and gasket/washer that needs to be tightened from under sink. Can be tricky as getting to underside of that area of sink is usually a tight area, and the nuts are good size. Most hardware stores will have a faucet nut wrench which has a swivel head for on and off and is designed to reach that area vertically. You might be lucky and have plastic nuts with wings that will allow you to tighten by hand. Word of advise, that area and related hardware can play havoc on the knuckles.

Moen Plumbing | Answered on Jul 14, 2019


If this a new circumstance it could a few things causing. If the spout has a button on it to divert water to shower, it is probably a blockage in nipple. Just remove spout, clean all debris buildup. If you have a diverter valve (Handle) it's most likely blockage in valve. This is assuming shower pressure is normal.

Plumbing | Answered on Jul 14, 2019


There are screws that come up through the bottom. You may have to remove the faucet to tighten it. While you have it out, throw it away and buy a new one.

Moen 7840... | Answered on Jul 13, 2019


sounds like you need to check the grommet between the motor and the pump. If this grommet connector breaks, the motor will come on but the pump will not work. Turn the unit upside down and look where the motor connects to the pump. Be aware if you can lose your oil while turning upside down unless you cap the port and exhaust. If this is it, go straight to the Robinair web site and you can order one for around $25.

Robinair... | Answered on Jul 12, 2019


Disconnect it and draw it out of the hole.

Plumbing | Answered on Jul 12, 2019


https://www.youtube.com/watch?v=KrqJnXksvnQ

Moen Plumbing | Answered on Jul 06, 2019


Replace the battery CR2032 then you can see the LED colour.
Green: Your filter is working.
Half Red and Green: Replace filter soon. Your filter cartridge has two weeks or approximately 20 gallons of life left.
Red: Your filter cartridge has reached the end of its life and needs to be replaced now.

Plumbing | Answered on Jul 03, 2019


If it’s not making this noise for any other faucet, it’s probably one that has a hose sprayer. If yes, then there is a faulty diverter check valve in the faucet that wouldn’t red to be replaced. If your not handy, by a new faucet.

Plumbing | Answered on Jun 30, 2019

Not finding what you are looking for?
Plumbing Logo

14,835 questions posted

Ask a Question

Usually answered in minutes!

Top Plumbing Experts

Brad Brown

Level 3 Expert

18136 Answers

Tom Chichester

Level 3 Expert

55370 Answers

Gil Shultz

Level 3 Expert

3388 Answers

Are you a Plumbing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...