Measuring Tools & Sensors - Recent Questions, Troubleshooting & Support

Same exact features, buttons and functions as this manual by Irwin.

http://www.irwin.com/uploads/documents/36_laser_tape_25.pdf

Question moved from Washing Machines category. Unfortunately no one sells parts. You may be able to get a generic switch from an electronics parts retailer or somewhere like RS Components. There is one advertised for sale for $29! https://www.google.com/search?q=LazerPro+2062+level+parts ..

Not displye for redlighte

Question edited for clarity and add maker. Question moved from Cars and Trucks Category. On mine, there is no catch, you just wiggle it off. https://www.google.com/search?q=gvd-3504+voltage+tester+replace+battery ..

See this response: http://www.fixya.com/support/t2316205-change_battery_in_gvd_505a_tester

Leica ts09 serial no 1357844 puk code

Well, I opened a DW077 today as it didn't wanted to turn on. It was brought to me by a neighbor and he hadn't a clue what made it stop working. I removed the outside screws and rubber feet using a Torx T10 with a hole in the middle. Be careful not to remove the screws arranged in a square pattern as these hold the steppers in place. You don't want to mess with calibration ! Also be gentle with the rubber around the rotating head. You need to remove the metal ring on the outside to detach the rubber grommet.. Once open, there is not much to be found inside. There is one pcb, two steppers and some other plastic stuff. Measuring over the big cap indicated 0.9v and over the small cap I had a unstable low voltage. After desoldering some wires, the underside of the PCB can be inspected (all components are on the underside). What I found there was that the main capacitor (1000µF 50v 105°C) of the 5v voltage regulator circuit was blown and leaking electrolyte. Not only was the capacitor gone, it also took an SI4532A mosfet array with it. The 3A fast chip fuse was still intact. The circuit pulled +- 10mA at rest and it went up to 20ma when depressing the power button. That SI4532A chip consists of a P and N mosfet in an SOIC 8pin package. The N side had a hole and the pins were blackened. My guess is that this controls the power on-power off signal that goes to the LM2596-5 buck regulator. I have made some pictures of the damage. So this is a route to research. Hope it helps someone

No parts for that one. Complain to them. https://www.google.com/search?q=acu-rite+00605+replacement+parts Amazon carries some parts, but a brand new unit is only $20. ..

I want to use an old sensor forgiven during 30 years. I have no more manual, off course. Thanks for your answer

Most moisture meters measure the moisture content of wood or concrete is measured in percentages. So if the reading says 15 that means that there is a content of 15% moisture in the concrete.

The really fine wire is soldered from the RED terminal on left to the RED terminal on the top left (underneath the board). See below in the images.

how can i get resistor R10 22W and R10 21 W

I believe the GTS-6XX series is the non robotic version of the GTS-8XX series. And E-99 in the GTS-8XX series is when the station cannot write to it's internal memory. Try resetting it. If it comes up with the same error, the ABS circuit board needs to be replace. Unfortuinately parts have not been available for that unit for a long time.

What is it that your curious about?

Pressing the - (minus) button on the back toggles temperature units. Pressing + (plus) toggles barometric pressure units.

English language please.

Question edited for clarity. Full 'make model (what it is)'. Did you put batteries in both units and in the right order, sensor first? Step 1: Insert 2 fresh AA, batteries into the TX29U-IT sensor according to the polarity marked in the battery compartment. Step 2: Insert 2 fresh AAA, Alkaline batteries into the wireless thermometer according to the polarity markings. Step 3: After 5 minutes place sensor outside in a shaded location. https://www.lacrossetechnology.com/products/WS-9160U-IT#support Retired unit so no further warranty or parts. You can still get one on Amazon

La Crosse Technology WS-9160U-IT Digital Thermometer ...

Amazon.ca https://www.amazon.ca > Technology-WS-9160U-Digita... Digital thermometer with wireless remote and clock; Remote sensor transmits from up to 330 feet; records daily high and low temperatures; Receives weather ... Rating: 4.4 · ‎ 7,970 reviews · ‎ $31.50 · ‎ In stock ..

It's possible that one of the newer sensors could work in place of your 1457 sensor, but it depends on the specifications of the newer sensors and the compatibility with your base unit. The I MAX1457 sensor, which is a highly integrated analog-sensor signal processor optimized for piezoresistive sensor calibration and compensation. However, I have no information about its compatibility. If you're looking for a replacement sensor, I suggest contacting the manufacturer of your base unit to inquire about compatible sensors. Alternatively, you can check the user manual of your base unit to see if it lists compatible sensors. Garage door opener sensors are not universal. Safety sensors can only communicate with garage door openers from the same brand.

Unlikely unless you know the secret maker name and can find them in China. At the moment, no one has heard of it apart from here on Fixya. All questions need FULL 'make model (what it is)' please. https://www.google.com/search?q=dse+z111 ..