Braun Logo

Braun Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 535 Products
  • 5K Answers
  • 362K Views

Hello, Unfortunately, E01 is an error meaning a problem with a component internally that is not repairable. Please contact the customer service team for further .

Braun Health &... | Answered on Jan 31, 2020


Buzzing means that the motor is energized, but something is jamming the grinder gears. The could be something metal, or it could be that the bearings are dry and seized. You need to strip it to find out.

https://www.google.com/search?q=Braun+KSM2+grinder

Braun Coffee... | Answered on Jan 27, 2020


The drive unit is probably not seated correctly. It must be pushed down when reassembling in order to keep the motor contacts in the correct position until the case is secured

Braun Health &... | Answered on Jan 27, 2020


I need this lid! If you ever have no need for your grinder, I'd love the lid :)

Braun KSM 2... | Answered on Jan 15, 2020


Google (braun)(4169)(manual) without parens OR contact Braun directly to request.

Braun Blenders | Answered on Dec 28, 2019


It looks like a horn it is actually a picture of the thin plastic cover that goes over the end before you put it inside the ear. Put the cover on and it will work.

Braun IRT3020... | Answered on Dec 01, 2019


I took the file on a nail clipper and turned the impeller inside the unit. Remove the cleaning fluid from the unit. Turn the unit upside down, On the part that sticks into the large hole of the fluid reservoir you'll see the impeller. Just turn it it enough to dislodge any whiskers and try it again. Worked for me. Good luck

Braun Health &... | Answered on Oct 27, 2019


I struggled with this for a while too till I found a diagram. Place the wire spring and the flat detente spring (all the way to the bottom of the slot) in as shown in this diagram. When the trimmer plate goes all the way in, the spring will snap into its correct final position. Lee
trimmerspringinstallposition-wcjy5cljug2w44525vz1ol4j-1-0.png

Braun Health &... | Answered on Oct 24, 2019


Contact Braun directly to inquire.

Braun Health &... | Answered on Sep 28, 2019


shaveroutlet.com does repairs. email them at info@shaveroutlet.com

Braun Health &... | Answered on Sep 25, 2019


Why do you need to get into it? All Braun products have locking clips along the split edge. You need to use a plastic 'bludger'. Better to take it to a Braun Service Centre.

Braun Blenders | Answered on Sep 16, 2019


I don't know about this specific model of Braun shaver (I have a Braun Model 7526).

I have looked at the instructions for a couple of models of Braun Shaver, and the instructions are similar so it may help you to replace the batteries in yours.

Here is one of the instructions:
Braun 7526 battery problem
http://www.fixya.com/support/t1171024-braun_7526_battery_problem

Open the shaver:
1) Use a small flat screw driver pry off the bottom (where the cord plugs in)
2) Remove the silver sides
3) Using a small torq driver remove the 4 screws
4) Open shaver
5) Remove circuit board with batteries
6) Remove and replace circuit board with batteries (or solder in the new batteries)

And here is a link to instructions for a few different ones:
http://www.fixya.com/support/t1094906-needs_new_batters_open_razor_7526

http://www.fixya.com/support/t6710169-change_battery_cost

http://www.fixya.com/support/t771258-braun_battery_replacement

Braun Series 7... | Answered on Sep 01, 2019

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Braun Experts

Brad Brown

Level 3 Expert

18165 Answers

Tom Chichester

Level 3 Expert

55370 Answers

ray gallant

Level 3 Expert

66482 Answers

Are you a Braun Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...