Bosch Washing Machines - Page 6 - Recent Questions, Troubleshooting & Support

The blower motor is protected by the filters, so it shouldn't have an issue. The motor is hidden deep inside. Basically, you just undo every screw that you can find. Lay everything out in order and take pictures. https://www.google.com/search?q=Bosch+BGS4UGOLD2%2F11+vacuum+disassembly ..

The motor is losing its power due to dry bearings or burnt windings. It will probably need to be replaced (after 8 years..wow!).

Contact a Bosch technician. You may have to at least pay for a service call.

E20 error code: Short or break causing incorrect resistance in winding of the circulation pump or the motor. D10 error code: Cause: Wiring/electrical fault related to motor triac. Action: Check wiring on/to PCB and motor. Check the triac (on the PCB). C01 error code: Cause: Motor tacho fault. Action: Check motor and motor tacho wiring for problems.

Slide a couple of sheet of newspaper under the machine and leave it a while and pull it out. The drips will show the approximate location. Then you can pull the machine out and lean it against the wall to check underneath. Make sure someone is steadying it. The most likely is a faulty water inlet solenoid valve.

This washer has a built in self diagnostics feature.
What you do is: With the selector knob in the off position, press and hold the "menu & select" buttons, then turn the selector knob to the "permenent press cold" until the display comes on. This puts you in the diagnostics mode, in which the last 8 errors codes will be displayed. At this point the display should read:
START-MENU T1:ERRORS
LA-Er:-------.
It gets a little hard to explain from this point on, but in my case I was able to scroll through the errors using the menu button, and I found that the were 7 errors related to the "FLOW THROUGH SENSOR".
I had already replaced the door latching mechanism without results.
Now I am going to replace the flow through sensor and see if that works, I will let you know what happens.

I have in depth information about the Axxis wfr2460 that will most likely be very helpful to owners of this machine, but I don't know how to attach it to this forum, so if you like, contact me: [email protected] and I can send you the info that I have found. It explains the whole testing procedure as well as defining the error codes, which may save a lot of frustration in solving your problem.

I have never heard this before, but worth a try Resetting your washing machine

• First, you should perform a general reset of the machine. Turn the machine off at the power outlet, wait for one minute, and then turn it back on.
• If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians. Open and close the door of the washing machine 6 times within 12 seconds. Then, run the rinse/spin cycle without clothing to see if your problems are resolved. If it drains, problem solved!

• Nothing in the manual
• https://media3.bosch-home.com/Documents/9001346934_B.pdf

https://www.hunker.com/13410561/how-to-reset-a-bosch-washer

please download the user manual from the manufactures website its normally free and look at the trouble shooting guide for help on the subject eric

possibly a bad control board .

Pull them

https://www.manualslib.com/manual/1916755/Bosch-Professional-Al-1820-Cv.html

On some Bosch models, E00 indicates that the machine is overloaded. Alternatively, the load is too heavy when wet. The machine can't safely spin the load. You may need to take this blanket to a laundry mat and use their commercial size washer. Try running the washer when empty. If the error recurs, then the problem isn't the blanket. Instead, the motor is working too hard to spin the tub. This could indicate a problem with the motor or the pulley and hub that connect the tub to the motor. I wish that I had better news for you. Cindy Wells

BAD CONTROL BOARD??

If your washing machine makes a loud rumbling or repetitive banging sound, which is particularly bad on a spin cycle, then it is most likely due to loose or worn out drum bearings.

Did you read the manual ?

https://iinjaz-alkhalj.com/

so order replacement or notify repair shop

If there is an f57 error code, in 80% of cases the problem is related to the motor control board. But do not rush to buy a new one for your Bosch washing machine. When you solder the components of the board, they may be damaged as a result of the strong vibrations of the machine. Therefore, you need to monitor the correct and stable installation of your washer. In many cases, an experienced master can bring the device back to life. It will significantly save your budget. Think before you start an independent repair. Remember that the new electronic unit is quite expensive.

POSSIBLY IT HAS A BAD CONTROL BOARD .

BAD CONTROL BOARD