American Standard Logo

American Standard Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 681 Products
  • 4K Answers
  • 338K Views

have you ever heard of google search???

https://www.google.com/search?q=5395.700.020&rlz=1C1CHBF_enUS757US757&oq=5395.700.020&aqs=chrome..69i57.424j0j8&sourceid=chrome&ie=UTF-8

American... | Answered on Feb 11, 2018


Yes you can replace the handles as they are available from American Standard, directly. Go to their web site, parts and service, and select you mod. toilet. Order from them. https://www.americanstandard us.com/bathroom/toilets-category

American... | Answered on Feb 05, 2018


First, make sure the water feed to the tank is wide open, then make sure you have the inner workings set at maximum water level.

American... | Answered on Feb 01, 2018


The number of flashes indicate a fault there is a code on the door panel

American... | Answered on Jan 31, 2018


I would check with my LOCAL plumbing supply house .

American... | Answered on Jan 27, 2018


If by push pull you mean there is a knob and rod that you use to raise and lower the plug. Look under the sink for a rod extending perpendicular to pipe it will be about 8" long and attach to a linking bar below he push pull rod. Typically there is a small retaining nut that seats around a ball seal on this rod that secures it to the tail piece dropping from sink. Unscrew the retaining nut, slide the rod out and then lift out the plug. You will notice a ring on lower end of the plug piece that you will need to insert the rod thru when reassembling. If you are referring to a fixed twist and drop plug Open it and there will be a set screw on a flat face in the stem portion under the cap. It's usually small straight slot screw but may also be a hex head slot Loosen that screw and the plug will lift off a center peg in the drain assembly.

American... | Answered on Jan 12, 2018


I would google it . Or look on u tube

American... | Answered on Jan 12, 2018


are you sure its the floor connection as it could be the tank one, also if the floor section is there a insert sealed and fitted to the existing floor pipe and then the wax seal around this. similar model video. https://youtu.be/LebANJC2rx4

American... | Answered on Jan 11, 2018


low pressure error

If you need further help, reach me via phone at https://www.6ya.com/expert/thomas_092728000e6acb79

American... | Answered on Jan 02, 2018


go to a plumbing store and ask them what needs done. or check at local library for a manual to read on plumbing . were it my daughter she would call and ask me for help and of course I would go .

American... | Answered on Dec 24, 2017


possibly needs new seals in it .

American... | Answered on Dec 24, 2017


perhaps if you look on the correct website you will find what you want .

American... | Answered on Dec 24, 2017


You should look at your furnace and see if any safety lights are flashing. Make sure your thermostat is set to heat.Check system your using for updates.

American... | Answered on Dec 11, 2017


I see so many problems with these. make sure your thermostat is set to heat. if its hard wired simply turning it to the degrees it shows a bit past, should turn it on.If not check the heat source for any blinking lights which means a malfunction on the heaters it self... If you checked fuse box sometimes to flick the switch to off and back on does the trick to reset it.

American... | Answered on Dec 11, 2017


I'm contractor for the last 17 years and this is the first time I have problems with the toilet tank installation , I bought four toilets, three of them had a leaking tank I thought that the place that had bolt did not have enough pressure and I put more pressure every five minutes but the toilets kept on leaking, I took the bolts out and I put plumbing putty in the top and the bottom and installed it again but it kept on leaking then i removed the putty and i put liquid teflon on the bolts and finally the leaking stoped. Edit your post: insert-link-blue._v192249896_.gif To insert a product link use the format: [[ASIN:ASIN product-title]] (What's this?) I'm contractor for the last 17 years and this is the first time I have problems with the toilet tank installation , I bought four toilets, three of them had a leaking tank I thought that the place that had bolt did not have enough pressure and I put more pressure every five minutes but the toilets kept on leaking, I took the bolts out and I put plumbing putty in the top and the bottom and installed it again but it kept on leaking then i removed the putty and i put liquid teflon on the bolts and finally the leaking stoped. cancel-glossy._v192250345_.gif deletepost-glossy._v192250344_.gif Guidelines

American... | Answered on Dec 07, 2017


you are wasting your time complaining on fixya site
the correct action is to take the lot back and get a refund for a product -not fit for the purpose ---

American... | Answered on Dec 06, 2017


Wow, you are going to have a heck of a time finding that. Try contacting American Standard. They may be able to help you.

American... | Answered on Dec 05, 2017

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top American Standard Experts

Fahr Quad

Level 3 Expert

736 Answers

jdthefixer

Level 3 Expert

746 Answers

Tom Chichester

Level 3 Expert

54386 Answers

Are you an American Standard Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...