American Standard Home - Page 10 - Recent Questions, Troubleshooting & Support
How to install a sink
Hi huc0,
I'm Harvey the Master Plumber.
Your problem is: You need some instructions on how to install a sink in your
new house
We could set up an on line chat right here at a convenient time for both of us. I can talk you through it. It would be helpfull if you had the ability to take pictures and up load them at that time so I can see what you've got. The only sink I don't recomend for homeowner installation is a pedistal sink. They are very difficult even for a plumber.
Feel free contact me again!
Please give me a rating here at fixya.com before you sign off
Thank you,
Harvey your Master Plumber
3/22/2014 12:18:17 AM •
American...
•
Answered
on Mar 22, 2014
I want to clean the jets in my tub they look mouldy
Cleaning your Tub
There are several options for cleaning the piping on a jetted bathtub.
The reason you have a residue on the bathtub surface when you are done bathing is because there is bacteria built up in the plumbing of the jetted tub. In order to remove that and reduce the amount of "yucky stuff" coming into the tub when using it, we recommend a regular usage of a jet cleaning product about once every couple of months
Here is a link at the bottom to the cleaning products I can find right now. There may be others out there that I am not aware of but I do know these products work well in all jetted bathtubs.
US Parts Center
Bath Parts Plus Bath Pump Spa Part Spa Accessories Powered by Network...
3/17/2014 9:22:51 PM •
American...
•
Answered
on Mar 17, 2014
I have a problem with
Hi keithn60...
I had the same problem one time with my toilet tank, the answer is to put some silicone on the seal washer between the take and bowl assembly and to use a level on the tank to tighten it just enough to be level and not leak.
Please take time to rate me
3/12/2014 1:36:25 PM •
American...
•
Answered
on Mar 12, 2014
About every 20 minutes or
The flapper that stops water from entering the bowl after flushing needs adjustment. The chain is probably to short.
3/12/2014 1:33:45 PM •
American...
•
Answered
on Mar 12, 2014
My toilet keeps leaking from tank to bowl--replaced all internal parts
If the flapper and all has been replaced. then it must be worn out where the flapper sits. or its not smooth.check to make sure it is smooth where the flapper closes, and make sure it closes fully when flushed. you might be better off with a new toilet, but thats up to you!
3/12/2014 1:29:16 PM •
American...
•
Answered
on Mar 12, 2014
Down stair toilet bubbles when upstair toilet is flushed. never had this problem with old toilet
The roof vent for the toilets is shared. It is the pipe (on the roof) that lets water in the drain system. When clogged, it causes what you have. A garden hose placed in the roof vent (and turned on) may clear the blockage (could be leafs or pine straw or a dead bird). Needs to be cleared... I have used a plumbers snake with 100% success....but you may not have one...so the garden hose suggestion. Be careful on the roof.
3/11/2014 3:50:29 AM •
American...
•
Answered
on Mar 11, 2014
I have a jetted tub and it won't turn off. I have a single button in the back right corner and i don't know what to do!
Right now you are having to turn it on/off by using the circuit breaker or just unplugging the pump right?
Is this a button you depress or an electric button like you would find on a microwave?
If it is a button you depress to turn it on/off then the problem is most likely the air switch located in the motor under the skirt of the tub.
If it is an electric button then it may be the control box under the tub that needs to be replaced.
Rod
US Parts Center
888-521-6183
2/26/2014 11:24:57 PM •
American...
•
Answered
on Feb 26, 2014
We have 3 toilets in the house. the tanks won't refill after flushing
You may have dirt getting into your water from the well and clogging the fill valves in your toilets. Valve assembly can be opened and cleaned out from the top. Instructions are available on AS website for your model. (Note) If you are picking up material from your well, a sediment filter should be added to your water line.
2/1/2014 1:30:37 PM •
American...
•
Answered
on Feb 01, 2014
Change float level
Possible float adjustment is stripped. Replace float assembly. Or float is making contact with tank or flapper. Observe when flushing and turn assembly to operate freely position and tighten assembly nut under tank to secure.
2/1/2014 1:19:22 PM •
American...
•
Answered
on Feb 01, 2014
Water wont stop running
Water is either running (1) into the overflow tube or (2) out to the toilet under the flapper at the bottom of the tank. If (1) lower the ball or float. Done differently depending on model. If (2) replace the flapper with new flapper designed for your model. (Note: Raise manually the float valve and if water still runs out the little tube that goes into the overflow tube then fill valve is defective. Replace it.)
2/1/2014 1:12:36 PM •
American...
•
Answered
on Feb 01, 2014
Not finding what you are looking for?