Amana Heating & Cooling - Answered Questions & Fixed Issues

The compressor is not kicking in I need to know the right size and replace it

The important consideration is the rotational speed and adding extra horsepower really doesn't achieve anything because the motor isn't really under 'load' as it would be in say a winch. It is better to stick to OEM Specs https://www.google.com/search?q=amana+80+sse+blower+motor ..

the unit needs to be programed to operate in heat and cool mode

Question edited for a lot more clarity. The new improved energy efficient versions.

The Improved Amana R-410A PTAC Unit Uses Less Energy

Amana PTAC https://www.amana-ptac.com > products > ptac Looking to buy an energy-efficient PTAC unit for your building? Buy the new Amana R-410A PTAC unit heat pump, which reduces energy consumption by 35%. Probably this one. Talk to your installer. https://www.amana-ptac.com/products/ptac/hec154j ..

Question edited for clarity and toss in some CAPS. You can get wired or wireless. https://www.amana-ptac.com/products/ptac Fitting https://www.google.com/search?q=amana+ptac+connect+to+wall+thermostat .

Maybe something here will help you.... https://ptac4less.com/blog/troubleshoot-reset-amana-ptac/

Does the power light come on? If yes, then you can do a reset as below: There is a master switch on the bottom left of the control board. Slide that to 'off' position. Then press the hot and cold switch/key together and then slide the master switch back to 'on'. Please put your response/observation here if that does not work or there is power light as asked on top. Thanks

Hydronic switch open 9 E9 Hydronic switch open (if hydronic configured) - either the aquastat is defective, or the aquastat wiring is cut, or the aquastat is not present at all and the aquastat wires were not permanently connected together as per the set-up instructions.

diagnostic codes for ptac/pthp electronic control

https://www.google.com/search?q=Amana+PTAC+error+code+09 ..

i'm not familiar with your specific unit but ..sounds like an electronic gas value has gone bad or has a bad connection when that happened to my friend it wasn't that expensive to have it fixed .. BYW it acted like this for a while then stopped working completely

Usually when the furnace blower motor runs all the time
The limit switch or rollout switch is usually open or bad.
The furnace board is seeing that one of those switches is open, so it brings the blower on to try to get the heat out of the combustion chamber area, so the switch will close. But if the switch is bad and won’t close, the furnace board will keep the blower running continuously.

Hi, Please hit the "constant fan" button until the "on" button is removed from your Amana screen. Thank you.

bad control board

blower capacitors or motor bad

you will need to call for service. if it needs freon you cannot recharge it freon is expensive and requires a license.

not sure i use mine without exhaust hose

To operate the unit without having the remote .. Turn the unit OFF and unplug it for 15 minutes. After the time has elapsed, plug the unit in and turn the ON/OFF Switch to ON. You should now be able to operate the controls on the unit itself. As it should have reverted back to the original factory setup settings.

Hope this helps you and thanks for choosing FixYa.

copy and paste https://www.amanaparts.com/Shop-For-Parts/a4b1d693274/Model-ATB2232MRW00-Amana-Refrigerator-Parts?n=3

Self evaporating simply means there is a drain pan with a heater device installed that will evaporate and condensate that drains from the unit into the pan.

You do not need the external drain pan unless the unit makes more water than the drain pan and drain pan heater can handle.

switch thermostat to emergency heat. Call for service the unit should be under warranty. Be aware that using heating strips will cause your electric to go extremely high.