Acer Televison & Video - Answered Questions & Fixed Issues

Refer to page 129 of service manual Acer Aspire 5332, 5732Z - Sevice Guide. www.s-manuals.com.

Help in the link, but you probably need dealer service. https://www.google.com/search?q=Acer+X110P+does+not+light ..

Hi, Please start by switching the outlet that you use to power your projector. If you're not currently plugging the projector into an outlet but using a power strip, you can test that the power strip is still functioning by using it with other items. Thank you.

check the mute button

As Bob Myers mentions, the question can't be answered unless you explain which video output the camera has. The solution for a BNC CCTV camera would not be the same for a PoE IP camera. Provide that information, and we can suggest hardware that would connect your TV sets and project to the camera feed.

If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/ faults & possible causes to LCD screen are given with illustrations. You can get an idea about the fault to an extent.

Statistical Process Control TrainingAll Acer TV models use the universal Remote Control code NEC 18E7, which most of universal Remote Controls can use. We recommend using the search function, available on most universal remote controls, to find the compatible code for your Acer TV.

go into settings and find "ease of access" or "accessibility" and click on it the option to turn off closed captioning should be in there.

Hi I found a video for you on how, just click on link and it will take you there, All best Clive From N/Wales

The problem with power fluctuations is the Surge Power that exists when Power Is Restored. That passes excessive current to the TV Controller circuit and can blow the circuit board. Sound like that has happened to you. IN THE FUTURE...always use a UPS (Uninterruptable Power Supply) approximately 1000 Watt unit. It has a battery back up feature and filters the line Voltage. It protects the appliances and saves you grief. Walmart has them, Amazon too.

Something is shutting down your power supply

You can use the "RGB" input in the video input menu of the TV. If you don't have that then you can't hook the PC to this TV.

Almost .

Main system control memory IC fault. This is a very small IC; have 8 solder terminals, and can be located very near to the main system control-chroma IC. Check and replace it. Be sure to replace it with the same number printed on it; in all respect. Otherwise, it won't go. http://electronicshelponline.blogspot.com/ Before replacing it, try a reset to this set, and then check. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked here.

The most common failure in LCD monitors is capacitor burnout in the power supply. If that was the issue, and the service tech used the same brand of capacitor or a substitute with an inadequate ripple current rating, the problem would happen again. I have had excellent results using Panasonic FR-series capacitors as replacements, especially if there is space to go to one with the next higher voltage rating (usually also has a higher ripple current rating). The price is not too high if purchased from a general components supplier such as Mouser Electronics or Digi-Key Corporation. A burned-out capacitor would have a domed top and may show signs of leakage through the safety vent cut into the top. Compare the bad caps marked in red with the good one on the right:

Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/ In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.

First you will need to find out your wifi connection is ok or not basically, If you are having a slow Wi-Fi connection problem, its not the adapter, but might be the router. I found this article, which might help you to solve your problem. How to Change Wi Fi Channel for Your Router

Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis. http://electronicshelponline.blogspot.com/ To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced. To some models of sets, all these section circuit will be integrated at its main board. If this is the case, you have to replace the main board.

My TV has a spot when I go to program channels that says Cable or aerial. if you are on cable the aerial button will not work. Same the other way around. Make sure its programed on what you are using.

I Was watching generations all of a suddenly my decorder starts scanning continuosly