Questions & Answers for: Hyundai 98 degrees

Question about 2006 Sonata

98 saturn trans won't shift into drive

98 saturn trans won't shift into drive after car has ran for a while it will not shift into drive but if you shut it off and cut it back on it goes back to working fine . at least until it does it ...

Question about 1998 Elantra

2 Answers

Whats the torque for the head bolts on a 98

...on a 98 hyundai elantra The cylinder head bolts need to be torqued at 10MM bolts 22 FT-LBS 12mm bolts 26 FT-LBS + 60 degrees and then another 60 degrees.That torque will leave a blown gasket for

Question about 2001 Accent

1 Answer

Just need the torque secuence in the accent 2001

just need the torque secuence in the accent 2001 for the cylinder head bolts 1.5L cylinder head bolt torque step 1 18 ft lbs. step 2 60 degrees step 3 additional 60 degrees 1.6L cylinder head bolt ...

Question about 1997 Accent

1 Answer

WHAT TYPE OF OIL GOES

WHAT TYPE OF OIL GOES IN 1997 ACCENT. 10W-30 OR 40. Depends what temperature the vehicle is in most of the time 0 degrees to 50 degrees 0W-20 30 degrees to 70 degrees 5W-20 Then 10W-30 on up

Question about Motor 1996 Elantra

1 Answer

What are the torque settings of the j2 1.8GLS 1996

What are the torque settings of the j2 1.8GLS 1996 hyundai elantra cylinder head bolt torque 10 mm bolts step 1 22 ft lbs step 2 additional 60 degrees step 3 additional 60 degrees 12 mm bolts step 1 ...

Question about Motor 2004 Sonata

1 Answer

Torque specs for head on 2.4 dohc motor

torque specs for head on 2.4 dohc motor with used head bolts step 1 14 ft lbs. step 2 an additional 90 degrees step 3 another 90 degrees with new head bolts step 1 46 ft lbs. step 2 loosen all bolts ...

Question about 1998 Elantra

1 Answer

Big ends torque settings head torque

big ends torque settings head torque settings 10 mm bolts step 1 22 ft lbs. step 2 60 degrees step 3 additional 60 degrees 12 mm bolts step 1 26 ft lbs step 2 60 degrees step 3 additional 60 degrees

Question about 1998 Elantra

1 Answer

Head bolt and overhead cam bolt settings for hundai lantra 1.8 litre

...98 1.8L (VIN M) engines- Tighten M10 bolts to 22 ft. lbs. (30 Nm), plus 60-65 degrees, plus 60-65 degrees. Tighten M12 bolts to 26 ft. lbs. (35 Nm), plus 60-65 degrees, plus 60-65 degrees.Hope this ...

Question about 2005 Tucson

1 Answer

The head was done and I need the torque setting for this vehicle.

The head was done and I need the torque setting for this vehicle. The rockers and lifters were replaced. M10 bolts: 1st step; - 18 ft./lbs. 2nd step; - turn 60 degrees 3rd step; - turn 60 degrees M12 ...

Question about 2005 Tucson

1 Answer

Ignition timing advance at idle on OBD Foxwell - looks like no. 3,4,5,6 cylinders have a problem. See addition details

Ignition timing advance at idle on OBD Foxwell - looks like no. 3,4,5,6 cylinders have a problem. See addition details 2003 Hyundai Sonata GLS 2.7 V6 Cylinder #1 7.1 degrees Cylinder #2 7.1 degrees ...