Question about Samsung SyncMaster 710N 17" LCD Monitor
I bought this display used. I can't get it to display anything from the computer. The monitor passes the self test with the signal cable disconnected from the computer; there is a floating "Check cable" box as there should be. But as soon as I connect the cable to the computer the check cable box goes away. The green pilot light at lower right goes off and on periodically. If I press the menu button on the monitor I get no OSD display, but sometimes I get a graphic box in the upper left corner saying Test Good with a graphic of five small circles with dots in the center, arranged as a row of 3 and a row of 2. None of the other buttons does anything except the power button seems to turn the green pilot light off and on. I'm on a Windows XP system on a laptop with dual display, and I have run other external monitors and projectors off it with no problem. I installed the monitor driver. It seems like the monitor can't read the sync signals from the computer. I'm using a brand new VGA signal cable. The computer can detect that a monitor is connected. The monitor detects when it is connected to the computer or not. Can anyone help?
I used 2 resistor of 100 ohms (1/8W) to make one of 50 ohms. Like others instruction, just put the 50 ohms resistor between pins 5 and 6 of this chip and the problem is solved.
Posted on Aug 26, 2010
I tried 50oms(2x100oms, 1/4w), it worked for about one day and went back to original situation. Then, I found 4x218oms, 10w resistors, made a 55oms resistor. Now, the monitor works just fine.
Posted on May 12, 2009
I tried soldering a 50 ohm (actually it was a 47 Ohm resistor, 1/4 watt) between pins 5 and 6 on the Novatek IC and that seemed to have fixed the issue. I have been running the monitor for over an hour now with no problems.
Posted on Jan 21, 2009
Microcontroller Novatek firmware is faulted (sorry for my eng)
Posted on Oct 31, 2008
Hi, i had the same problem with a same model monitor, the reason for this problem is a IC (IC200) in the main board on the monitor of course. The fix is cheap and easy, you just have to place a 50 Ohm resistor between pins 5 and 6 of this chip and the problem is solved. Here is the information (in spanish) i found, please give thanks to the autor, not to me!
PD: Sorry for my english!
Posted on Sep 27, 2008
I solved the problem by replacing the main IC board. Cost $40 and shipping. The monitor now works perfectly. If I had more time to fool around trying various resistances, or temporarily use a variable resistance for testing, I might have solved it cheaper. However, I'm satisfied.
Part source was www.partstore.com
Samsung ASSY PCB MAIN-STZ;MJ BN94-00689C $39.45 1 $39.45 Sub Total: $39.45 Shipping/Handling: $7.95 Tax: $2.86 GRAND TOTAL: $50.26
Posted on Nov 01, 2008
Hy my monitor (710n) is having half picture scrambled. The lower part of screen is that the upper is ok. Like somebody cut it with the knife. Will the 50ohm tweak work for this?
Posted on Mar 11, 2011
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: NO DISPLAY :(
the resolution setting may have been in inadvertently change to one that your monitor does not support you mentioned that you have another monitor that does work with your computer what i would do is to set the video resolution to the lowest possible setting and the turn off the computer and connect the questionable monitor to your computer and reboot if it does come up then you will be able to make changes and find an appropriate resolution for your monitor
Posted on Dec 28, 2008
Not completely sure what you're saying. Here's what I got out of your problem:
You have a Syncmaster 710n that displays a box saying the best resolution is _____ x _____, but your Syncmaster 710v doesn't show that message.
The main question I have to ask you is whether or not you see the screen or display behind the message on the Syncmaster 710n.
In either case, I doubt that this is a hardware problem. I also highly doubt that your monitor cannot be repaired. Try the following:
1) If you see the display/screen is showing behind the message box, this is almost definitely a setting issue. You need to press the menu button on your monitor and look for an option that says something like "display resolution message" or "ideal resolution message", or something else like that. Then you need to change the setting for that option, for example if "Yes" is selected, then you need to change it to "No" or if "Enable" is selected you need to change it to "Disable".
If you have the manual for the monitor, it should make it easier to know what setting to change. If not then go here:
and download the Manual that you need.
2) If nothing is being displayed behind the message, try to change the display settings of your computer. While using a different monitor, try the following: If in XP, right-click on the desktop and go to Properties, and select the tab for display settings and adjust the resolution to something compatible with your monitor (like the one it suggests you to change it to). If in Vista/7, right-click the desktop and select Screen Resolution/Display Settings and adjust it there.
Good luck. Let us know how it goes.
Posted on Feb 16, 2010
Tips for a great answer:
Jun 10, 2010 | Samsung SyncMaster 710N 17" LCD Monitor
Feb 16, 2010 | Samsung SyncMaster 710N 17 in. Flat Panel...
Nov 11, 2009 | Samsung SyncMaster 710N 17 in. Flat Panel...
Feb 24, 2009 | Samsung SyncMaster 710N 17" LCD Monitor
May 29, 2008 | Samsung SyncMaster 710N 17" LCD Monitor
Oct 29, 2007 | Samsung SyncMaster 710N 17 in. Flat Panel...
Jan 30, 2007 | Samsung 710N V2 (Ivory) 17 in. Flat Panel...
15,447 people viewed this question
Usually answered in minutes!