Can i use any drill bit for drilling ...........in any drill machine or different drill machine have thier own drill bit

A Drill Press is used by many woodworkers around the globe for its efficiency in perfect woodworking. Drilling can be done by placing the drill press on a table or larger models on the floor. It includes a steel column which connects the base to the top of the base. Here, the motor powering the chuck. It holds the bit is located.
One of its best conveniences is the drill woodworking operates using a geared mechanism. As a result, you can use the lever to rise or descend the bit.
Before you start your drill woodworking, it is necessary to know that the piece which is going to be attached should be kept on the table that is adjusted with the vertical column. Drill press offers another advantage that you can drill exactly straight or at an angle. You will be able to constantly drill in the same location with the help of a fence and stop block.
So, let us start our discussion on the use of drill press in drill woodworking:

• Drill woodworking needs correct measurements to secure its drilling location. You can buy drill guides from hardware stores or building supply centers. These can be available in a wide range of diameters. Place it on the surface of the work and insert the bit through the guide to drill like a professional.
• A drill press can solve your issue related to drilling guides. You can make a set of drill guides by your own by drilling different diameter holes in blocks of wood. But be careful while doing this as the holes in the wooden guide can differ from that of drill guides. Large holes may make it more difficult to position the drill.
• To align the bit, you should remove a square or rectangle of wood from a board. Then make a right angle with it and place the bit into a corner. Thus, a perfect alignment will be created.
• As you align the bit with the nail by touch, you should put a large-headed nail before with the head down on the surface of the board.
• Another trick that will keep your hole straight and perpendicular is by using an empty spool of thread or sewing machine bobbin. First, you have to mark the spot by making a start hole. You can mark with nail or ice pick. Now, the spool or bobbin should be kept in a place that the drill bit passes through it and then align the point with the start hole that was created by you before. Keep the flat end of the spool or bobbin securely with the drill in the 'off' position. Hold it against the surface and in place with pliers. Now, with this position, you can start the drill, and you will observe the hole will be drilled in a perfectly straight or perpendicular way.

These are few simple guides you can consider to drill woodworking. We hope the instructions will be helpful for you to drill holes flawlessly.
Source: Drill Woodworking Made Easy With Drill Press

The difference is the working action. SDS drills use a corrugated cams running against each other.

It could be that the drill bit is not well fixed, so make sure it is well fitted on the drill machine

You attach it on the machine after you have attached the drill bit. If the drill bit is 100 mm for example (4 inches) and you want to drill 50mm (2 inces) only then you make the drive guide to be 50mm (2 inches) ahead of the drill machine.

For the pictured drill motor, you put the bit in and use a "chuck key" to tighten the chuck onto the bit...

If the photo is not your machine but you have an SDS type chuck, you insert the bit, pull back on a collar and twist the bit until you feel it engage and release the collar. When seated properly you cannot pull the bit out without pulling back on the collar.

dear sir

please use drill bit remove key with drill machine and try to turn it anti clock vise then your bit will being loose and you can remove it easily .

thank you
hope answer the question
please vote !

The difference is the type of shaft on the bit so that it matches to the chuck type of the drill...They are NOT interchangeable!!!!
You need to know which type of check your drill has and order accorndingly...

heatman101

I had the same problem. I put the drill onto Hammer/Chisel action and it helped release the bit.

Most cordless drills use keyless chucks these days. Shift the drill into reverse and hold the main body of the chuck. Pull the trigger and the bit should come out. Put it into forward and run it to tighten onto a new bit.

If it's an inexpensive bit, odds are it's spinning in the chuck. If the chuck key can't tighten the jaws well enough, you'll need to borrow or buy a different drill (or you could replace the chuck).

If you bought an SDS bit (one with slots milled in the shank), you're best off buying a bit made for a standard drill. It's not impossible to get a SDS bit to chuck into a standard drill, but it's difficult and they often slip loose during drilling, messing up the hole.


Take care!