Starting coil switch I had to replace a bearing on my buffalo bench grinder and I cant figure out to put the starting coil switch back on or how it works

Usually, 4 wires are multi-directional neutral and earth are usually colours the other 2 are both live and would need to go through a switch. you can of course put the other live in a cover and just use one live wired as usual into a plug. Make sure the spare wire is well protected ie in a jb with plenty of tape around it

An adjustable centrifugal start relay and or capacitor problem.


Nonsensical Bench Grinder Wiring Diagram Diagrams Switch Buffalo 6cb 6510...

2 wires are not needed to use they are the wires of an supression capacitor on the switch then there are 2 wires from your power cable and 2 that goes to your motor that 4 you only you have to use you can also connect the 2 wires from the s-capacitor with te wires on the motor together thats is how its also correct, (but best is to remove it because its only for suppression for FM ukw radio signals and everybody has DAB+ and the change to have short-circuit is reduced.

The switch is probably generic.. go to a Lighting store and see if they have equivalent

If you can't find the direct replacement check with Grainger or other industrial supply house ... https://www.grainger.com/category/push-pull-switches/automotive-electrical-and-lighting/fleet-and-vehicle-maintenance/ecatalog/N-15m5?okey=push-pull+switches&mkey=Push%2FPull+Switches+&refineSearchString=push-pull+switches&NLSCM=5&EndecaKeyword=push-pull+switches&searchRedirect=push-pull+switches&sst=subset&suggestConfigId=6&nls_boost_words=noContent

That entire older Buffalo line of grinders: N-10CB, B-8CB, B-6CB, bgbr-6cb all use the same push pull switch.Most of those grinders were dual-voltage with a starter capacitor and there are 6 wires connected to a 4 contact switch. The "Jet BGS8-076" grinder switch that is used by the older Buffalo's, Galaxy, Duracraft and TestRite grinders is no longer available. The good news is that there is a replacement switch from another manufacturer: "3030-9001 push pull switch for RDX grinders" from Wholesale Tool is a direct replacement. It has the same 4-screw contacts on the back and the same push-pull diamond pattern front plate.

You could connect the wires of the switch together inside and bypass the switch. Then I would connect in the power cable a switch rated for 1 hp. You can use surface mount electrical box, with two cable connectors (one for the cable going into the grinder, the other for the cable going to the male cord end of the cable. Install a 120 volt switch inside the box (similar to the light switch in the wall). Make sure that the switch is rated for 1 hp. I would install the switch under the bench, under the grinder.

Joe

The neutral line should never be switched--only the hot wire (black). If there are only two wires that went to the switch, you should be able to tie them together and the motor will run when plugged in. The switch should be a common SPST type either toggle or rocker to fit. Hope this helps!

I had the same problem with a Northern Tools bench grinder. These are made in China and parts are hard to come by. I had enough room after removing the old broken on/off switch to install a single pole 15 amp light switch like you use in your home. I simply installed it horizontally and then put the switch cover on. It works perfectly. If you do not have enough room then look for any 15 amp or larger switch that will fit in the housing. Any on/off switch will work. You could even mount the switch on the bench in a switch housing and run the wires from the grinder to the switch and back if need be. Just be safe and make sure there are no exposed wires. As a last resort you could remove the switch connect the wires, eliminating the switch and use a plug in wall switch such as this.

You can get a replacement toggle switch at any hardware store look in the electrical department.