My Model # is 27957FE 1-A Dont know how to reset

i don't know about on line instruction.
but i could help you ....
there is two position for crown 1 and 2.
bring crown on position 2 and turn crown clockwise to change TIME, DAY & DATE.

bring crown position 1, and turn crown counterclockwise to change DATE.

your watch has Chronograph / Stop watch.
use that please press right TOP button chronograph will START, press again Chronograph will STOP.

Press bottom button to RESET Chronograph.

hope it will help

Hi John921,

Here is the step by step procedure to set date and time of your Garmin GPS 38......
It will definitely work......

Set Local Date and Time

1) Verify the date and local time (this should be
the date and time according to the local date and
time of country/area you are in). Because the
time shows is Universal Time (UTC), you will
need to enter a time offset to display the correct
local time for your area.

2) Move the field highlight to the OFFSET field
and press Enter

3) With the arrows (←→), go to the figure which
represents the hours then with the up & down
arrows (↑↓), select the time offset for your
longitude and press .

4) Move the field highlight to the HOURS field
and change to 24 if that is not already the case.

This will definitely work......
Please rate this solution............

Thanks......

annoyingmist, let me try.

1.by windy you mean mechanical?
2. if yes, then move the hands clockwise watching the calender until new date appears.
3. now turn hands anti- clockwise a little and clockwise again. Keep doing until you get today;s date.
4. set the watch to correct time. good luck.

my login user and password afaq_shamel Stccpe_2009 not working i cannot login my page modem-007 please help me

FYI, did you know about this, sorry no specs, hope this could help. TMM MILPITAS CA USA Make: MAZDA Model: 626 Model Year: 1999 Manufacturer: MAZDA NORTH AMERICAN OPERATIONS Mfr's Report Date: MAY 09, 2000 NHTSA CAMPAIGN ID Number: 00V134000 NHTSA Action Number: N/A Component: ENGINE AND ENGINE COOLING:ENGINE   Summary: VEHICLE DESCRIPTION: PASSENGER VEHICLES. AN EXTERNAL SPRING IN THE TIMING BELT TENSIONER COULD BREAK. Consequence: THE BROKEN SPRING MAY GET CAUGHT IN THE TIMING BELT, RESULTING POSSIBLE ENGINE STALLING. Remedy: DEALERS WILL CHECK THE TENSIONER INSTALLED AND REPLACE IT IF THE VEHICLE IS EQUIPPED WITH THE AFFECTED TENSIONER. Notes: OWNER NOTIFICATION BEGAN SEPTEMBER 28, 2000. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT MAZDA AT 1-000-222-5500. ALSO CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION'S AUTO SAFETY HOTLINE AT 1-888-DASH-2-DOT (1-888-327-4236).

Hi.

If you dont remember the BIOS password, you may remove it by resetting the BIOS password.

Please follow the below steps to reset the BIOS password:

1) Please remove the bottom casing of the Notebook.
2) Once you have removed the below casing, you should be able to see a CMOS Battery.
3) The CMOS Battery will be of a size of a coin.
4) Once you have found the CMOS Battery, please remove and re-insert it again.
5) The CMOS Battery will have the information about the Computer Date, time, BIOS Password etc.,
6) Removing and re-inserting the CMOS Battery will reset these settings, which will also remove the BIOS password.

Please perform the above steps and let me know the results.

Hope this helps.

Please feel free to contact for further information and assistance.

I just ran across my manual. My organizer died, but here goes. You have to set the home date and time as the city's date and time for your time zone. Press Shift-Home. Select 1 to choose the City. Cities are listed according to their country. Press U for United States. Press the up or down arrow to scroll. When you see your City or one in the same time zone, input that number. If DST in effect, press shift-number for the city. To set time, select 2,or Shift-Home-2. Set the time. Press enter. Good Luck.

Follow this link:
http://world.casio.com/wat/download/en/manual/

Rate me, please.

1. Switch the GT*RATE SET button to RATE SET.
2. Press the date/clock button to display current time.
3. Enter time wanted using military time. 4:52 p.m would be entered as 16.52 (Note the 16 is followed by . then enter the 52. (ie. 10:45 a.m. would be entered as 10.45)
4. Press the date/clock button again to enter new time.

Just reset mine and is current. If the built in battery needs changed, access panel is on the back. It uses a watch type battery.
~DLS

i hope this helps....
the top right says st/stp....tells you the year
the bottom right is the light...
the top left is the reset....
and the bottom left is mode...alarm, stop watch,and time 2