Targa 3100 video card..what does the red led "on"

if it is an USB card reader you should attach the pins to the usb header on the motherboard.
Not sure about USB3 devices but the wires should be RED/WHITE/GREEN/BLACK on USB 1 AND 2DEVICES.
If the motherboard header consists of two rows of pins, a row of four next a row of five pins then the red wire will go on the pin furthest away from the odd pin, I mean the extra one that is alone. Next to the red wire goes the white one then the green wire is next. The black wire will go on the pin directly next to the single pin, that is the earth wire.

this heater will display 2 red light related problem 1-service the system mean you need to clean you filter, and service the heater mean it may be a problem with the heater this 2 you will be able to see it in key pad control the heater ,now reset the board and see what happens (CUT THE POWER ON/OFF UNCE )

you may change the vga cable for your sync master, and try another video graphics card.

one more thing, if you happen to see that your monitor led goes orange, that would only mean it needs to be replace by a new one, or a technician might help you. orange led light means, internal problem.

only IPS can sure that. if model reset fails
no kidding call them. like millions do per day worldwide.
the ONLINE led must glow, the manual is clear about LED
and connected is no it, online is first. on modems and in this case the modem side of router./modem.
3347w = wireless
LED DSL goes green solid but blinks as DSK trains and conn.
and
LED interenet solid green connnected. blinks for data and red = fail.
page 205 in 3000 series manual
google it read it..

online means internet, and fails for you
and means call the ISP any time the internet led goes dead or red
it is that simple. do it.

You wil need to connect using a DVI to HDMI cable. You can get one for about 5$
http://www.amazon.com/DVI-HDMI-Cable-6ft-Male-Male/dp/B0002CZHN6
Just connect it and choose the HDMI input its plugged into(1/2/3). If there is nothing on the screen adjust the display resolution on your computer. If you are using 1080i then the resolution should 1920x1080

Try to pull out video card and clean the slot on motherboard then put video in. If no result replace video card.

Most of the Radeon video cards uses ATI catalyst. Try this site. FOllow the step by step procedure on how to download. Good luck

http://support.amd.com/us/gpudownload/Pages/index.aspx

depend on your OS as to how you go about this but basically click "start" the right click on "my computer" select properties. this will get you to system properties..slick the "hardware tab then the "device manager" button.

Find "display adapters" and right click on your current video card and select update driver. tell it no to search the internet then click on the "install from a list or specific location (advanced)" you the should come to a window where you can "browse" to and select the folder where your new driver is located. it will look for the .inf file and install the driver. This is a walk through using XP its gonna differ a bit on Vista but its basically the same thing.

I have a TARGA TRAVELLER 1574 X2 LAPTOP which is about 2-3 years old. I was using it last week, everything was fine. I put it away, but when i came to use the laptop later on, the screen was completely blank. The power button was lit up and everything else was ok, but no power was going into the monitor. Ive tried to see if it had gone into sleep mode, but to no avail. Ive even tried to reboot with a WINDOWS XP disk but nothing. Do you have a solution to my problem?

If your PC tells you the driver is not found, the card itself is working but the problem is in the software.
Chances are that a microsoft update caused this problem, specially if you pc is set to automaticly update windows.

Try re-installing the targa drivers, this might help.
Otherwise try to find out if there is a driver-update available on the relevant website of Targa.