Follow techexperts12 indications, he is the head expert on Fixya, Vote his solution Fixya, so that he can earn his well deserved money.
Thanks for using Fixya.
Worked before ? (washed in cold water selection)
reset didn't helped.
what are the conditions required in order for that machine to wash in cold water ?
sounds logical that the control may be malfunctioning. check again your user guide about required conditions for the cold water wash cycle to start.
×
U have to go with a professionl repairer
How old is this washer?
And is it a US machine or a European machine? These 2 are almost completely different machines.
Since they are so different, the cures can also be different.
Bosch comes with a 2 year exchange or refund guarantee on their machines. So if you are withing the 2 year time period, I would contact the local Bosch service center with your problem.
Also, has the machine had any other repairs done to it recently? Has it displayed any behavior that doesn't seem "right" Reason I ask can have a lot to do with what might be causing the problem. This is sounding like a controller card fault.
Or it could be that the display is showing an incorrect error code.
Lets cover the above questions, and go from there.
Dowloadable manual here
http://laundry.manualsonline.com/manuals/mfg/bosch/bosch_wfk_2401_tumble_action_clothes_washer.html
Check your cold water hose and make sure that the little screen is clean. On the back of the washer you will find two hoses. One will feel warm and the other cold. Turn off the washer and unplug it. Have a bucket and some towels nearby. unscrew the hoses and clean the little filters at the ends carefully. sometimes sand can get in there and completely stop water from entering. While you're there make sure your cold water valve is turned all the way on and that they hose is not twisted or flattened in any way.
I hope this works for you. Thank You for using Fix Ya!
Dear sir/madam,
Enter the test program by:
1. Set the cycle knob to any "X" (reset) position
2. Press and hold the Pre-wash and the Start buttons at the same time.
While still holding these buttons, turn the unit on by pressing the
On/Off button
3. Keep holding the Pre-wash and the Start buttons until the digital display comes on (about 5 seconds)
The digital display will show 00 for no faults or will show a fault code.
To end the test program turn the washer off at any time.
thanks
good luck
Its bosh
and follow me
Initially check the filter on your washing machine and clean if necessary, your manual should detail this procedure.
If your machine will not start or complete the programme, check:
What is the make of the washer? ge,kenmore,sharp.ect....
Try reset.unplug the machine n replug in n switch on after 5 mins.
120 views
Usually answered in minutes!
no luck with posted soloution,machine still in the same mode.
have tried several times to resetthis machine with no luck, window time display still shows code--CL--WHEN SELECTER IS ON NUMB--1---HELP,
THIS MACHINE IS ABOSCH WFK2401 THANKS
bosch washer still in the cl mode when no1 which is cold water wash cycle is selected,machine will operae on all other selections???????????
have followed all soloutions, to the letter,the last test came up with the code oo, which indicates no fault condition,however,the times showiing for temp and different wash cycles is all over the place,and most times its back to CL on numb1,have checked voltages at both ends-ok.
have already aproached the hose problem in the early stages off this problem,thanks all the same,beginig to suspect a control moudle malfunction,please check all my postings to see if i have missed anything---thanks
my machine indicates cl when you select no1 or no4---the rest off the cycle times are all over the place,I have run every test suggested, beging to suspect a control moudle failure????
this machine is 5years old,made in usa,I recently removed main drive motor to replace the brushes--------------is it possible that I did not reconnect the harness wiring from motor to the main harness the right way????
meant to get back to my last expert,semm ot have lost him ,machine displays cl on no1 and no4 the rest off the time cycles are all over the place,machine is from usa and is 6years old
thanks to every one for their efforts,though it would be good to know why cl appears on noi and no4 instead of the selected time cycle--------comment please, thanks again.
×