When the washer gets to the spin dry cycle, the washer will pump the water out but it doesn't spin. Took all the clothes out just in case it might have been a heavy load but even empty it wouldn't spin.

Question 1

0helpful

2answers

My maytag centennial washer(mvwc300vw0) spins and pumps but doesn't get the clothes as dry as it used to/should? I checked the drain hoses and they are not plugged up. Is it possible the holes i

If there is no water left after spinning them the problem could be the spin speed. Belt slipping

Oct 13, 2017 • Maytag Washing Machines

0helpful

1answer

Frigidaire Affinity Front Load Washer wont drain.

If your pump had something in it, it wouldn't have had to clog it, but rather just stopped the internal spinning. My coworker removed a dollar bill from his water pump, and it fixed the problem he was having (same as you've described) and the water pump worked well after it was re-installed.
Worst case scenario, you reinstall it and it doesn't drain and you spend 40 or 50 bucks online for the part. I would reinstall and see if it works. I'd bet on it.

Nov 14, 2012 • Frigidaire Affinity ATF7000ES Front Load...

0helpful

1answer

My Frigidare Affinity front load washer doesn't pump water on the Normal cycle.

Check the water inlet electro valve at the rear of the washer and make sure it is working.

Jul 25, 2017 • Frigidaire Washing Machines

0helpful

1answer

Water did not drain

see the causes and fix it. God bless you
If your washer won't drain, check these: It spins, but doesn't pump It doesn't spin or pump It pumps, but the water returns It spins, but doesn't pump If your washer spins but doesn't pump the water out, the drain line is probably clogged. In many washers, a small sock or other piece of clothing can get between the clothes tub and the outer tub that holds the water. If the clothing gets between the tubs, it may then get into the drain hose that's attached to the pump--or even into the pump itself. If it's in the pump, you need to remove the hoses from the pump and pull the item out. To remove the sock from the outer tub port, open the washer's main access panel and remove the large-diameter rubber hose that connects the pump to the bottom of the outer tub. Then, using needle-nose pliers, try to grab and remove the clothing through the port. Sometimes you can't remove the stuck clothing from below. Then you have to remove the agitator, top of the outer drum shield, and inner clothes tub. This isn't easy to do--and you may need special tools--so you might be happier getting a qualified appliance repair technician to do the job. If the drain line isn't plugged, the problem may be with your pump. Even if the pump appears to be turning, the internal impeller may be broken. If so, you need to replace the pump. It doesn't spin or pump If your washer doesn't spin or pump water out but the motor is running, your washer probably has a frozen pump pulley. If so, you need to replace the pump. To check the pulley, remove the pump from the washer and try to rotate the pulley manually. If it doesn't turn freely--if it's frozen or stiff--replace it. It pumps, but the water returns If the water that pumps out of the machine goes back into the machine after the spin cycle, your washer may be siphoning the water from a laundry tub that has a slow drain, back into the washer. The usual remedy for this is to improve the draining of the laundry tub. (Is something stuck in the drain?) Also, check for these problems: If the drain hose reaches more than about 4 inches into the laundry tub, cut off the excess. If your drain hose is lower than the washer's cabinet, install an air gap/siphon break assembly.

Sep 22, 2012 • Kenmore HE2 Plus Front Load Washer

0helpful

1answer

Washing machine does not empty

see the causes and use the common sense, God bless you.
If your washer won't drain, check these: It spins, but doesn't pump It doesn't spin or pump It pumps, but the water returns It spins, but doesn't pump If your washer spins but doesn't pump the water out, the drain line is probably clogged. In many washers, a small sock or other piece of clothing can get between the clothes tub and the outer tub that holds the water. If the clothing gets between the tubs, it may then get into the drain hose that's attached to the pump--or even into the pump itself. If it's in the pump, you need to remove the hoses from the pump and pull the item out. To remove the sock from the outer tub port, open the washer's main access panel and remove the large-diameter rubber hose that connects the pump to the bottom of the outer tub. Then, using needle-nose pliers, try to grab and remove the clothing through the port. Sometimes you can't remove the stuck clothing from below. Then you have to remove the agitator, top of the outer drum shield, and inner clothes tub. This isn't easy to do--and you may need special tools--so you might be happier getting a qualified appliance repair technician to do the job. If the drain line isn't plugged, the problem may be with your pump. Even if the pump appears to be turning, the internal impeller may be broken. If so, you need to replace the pump. It doesn't spin or pump If your washer doesn't spin or pump water out but the motor is running, your washer probably has a frozen pump pulley. If so, you need to replace the pump. To check the pulley, remove the pump from the washer and try to rotate the pulley manually. If it doesn't turn freely--if it's frozen or stiff--replace it. It pumps, but the water returns If the water that pumps out of the machine goes back into the machine after the spin cycle, your washer may be siphoning the water from a laundry tub that has a slow drain, back into the washer. The usual remedy for this is to improve the draining of the laundry tub. (Is something stuck in the drain?) Also, check for these problems: If the drain hose reaches more than about 4 inches into the laundry tub, cut off the excess. If your drain hose is lower than the washer's cabinet, install an air gap/siphon break assembly.

Sep 19, 2012 • Ariston Technologies Washing Machines

1helpful

1answer

I have a Whirlpool Ultimate Care II washing machine (model LSN1000JQ0). The washer will fill with water and begin to agitate. Shortly after it will stop and will not drain. I've cleaned all hoses

see the next steps and use the common sense: God bless you
It spins, but doesn't pump If your washer spins but doesn't pump the water out, the drain line is probably clogged. In many washers, a small sock or other piece of clothing can get between the clothes tub and the outer tub that holds the water. If the clothing gets between the tubs, it may then get into the drain hose that's attached to the pump--or even into the pump itself. If it's in the pump, you need to remove the hoses from the pump and pull the item out. To remove the sock from the outer tub port, open the washer's main access panel and remove the large-diameter rubber hose that connects the pump to the bottom of the outer tub. Then, using needle-nose pliers, try to grab and remove the clothing through the port. Sometimes you can't remove the stuck clothing from below. Then you have to remove the agitator, top of the outer drum shield, and inner clothes tub. This isn't easy to do--and you may need special tools--so you might be happier getting a qualified appliance repair technician to do the job. If the drain line isn't plugged, the problem may be with your pump. Even if the pump appears to be turning, the internal impeller may be broken. If so, you need to replace the pump. It doesn't spin or pump If your washer doesn't spin or pump water out but the motor is running, your washer probably has a frozen pump pulley. If so, you need to replace the pump. To check the pulley, remove the pump from the washer and try to rotate the pulley manually. If it doesn't turn freely--if it's frozen or stiff--replace it. It pumps, but the water returns If the water that pumps out of the machine goes back into the machine after the spin cycle, your washer may be siphoning the water from a laundry tub that has a slow drain, back into the washer. The usual remedy for this is to improve the draining of the laundry tub. (Is something stuck in the drain?) Also, check for these problems: If the drain hose reaches more than about 4 inches into the laundry tub, cut off the excess. If your drain hose is lower than the washer's cabinet, install an air gap/siphon break assembly.

Aug 01, 2012 • Whirlpool Ultimate Care II LSQ9564J Top...

4helpful

1answer

Washer will not spin at all no code . will drain and tumble back and forth,when it comes time to spin it turns off.

A washing machine is basically a big tub that repeatedly fills with water and then drains, spins to wring clothes dry, and has a device for stirring things up-- either an agitator in the middle of a top-load machine or a rolling drum in the case of a front-loader.
The four cycles that every washer performs are fill, wash, drain, and spin. Though these functions are pretty basic, a number of things can go wrong with them.
There are a number of problems that you can fix quite simply; some issues, however, are better left in the hands of an appliance repairperson.Problems that commonly occur with a clothes washer are discussed in depth below.If your washer doesn't run, be sure it's plugged in and that the receptacle works (the circuit hasn't overloaded). Before working on the washing machine, be sure to unplug it.
To prevent problems, follow good maintenance procedures. Use the right amount of detergent for your washer and your water hardness, make sure the machine is level, and don't overload it for the cycle chosen.

Washing Machine Does Not Fill
If the washer doesn't fill, the water inlet screens may be blocked. Clean or replace them. (Check your owner's manual for the location of the screens; they're often located at one end of the supply hoses, or you may have to remove a panel to access them.) Other reasons for not filling may be that either the timer or temperature selector is broken--both of these are repairs for an appliance repairperson.

Washer Does Not Spin
If your washer doesn't spin, check to see if the clothes have jammed or are unbalanced in the drum before calling a repairperson. Unbalanced clothes will also cause a w
asher to shudder or "walk." If straightening out the load doesn't stop the washer from shaking, look at the feet underneath and be sure they are properly adjusted to keep the washer sitting level on the floor (you just turn them to move them up or down).
Clothes Are Wet After Spin Cycle
If your clothes remain wet after your washer's spin cycle, perform the following diagnostics:
1) Lift the lid during the spin cycle. If the tub is not spinning, you may have a damaged motor coupler. Call a repairperson to replace this part.
2) If the tub is spinning, recheck the load to make sure it is balanced. If you are certain the load is balanced but your clothes are still wet, you may need to call a repairperson to replace a damaged motor pulley, tub bearing, belt, or clutch.

3) You can also follow the troubleshooting steps outlined in "Washing Machine Doesn't Drain." You may have a problem with your drain hose or pump.

Oct 27, 2011 • Washing Machines

0helpful

1answer

HI: My washer will not drain all the water out at the end of the wash can you help me out

Hello there and thank you for choosing fixya

Spin cycle If the washer doesn't reach its proper spin speed, the clothes may be too wet at the end of a cycle. Check to be sure the load is properly balanced and run a spin cycle again. If the clothes are still wet, you may have a worn or loose belt (Maytag®), a worn clutch (GE®/Hotpoint®), or a worn motor pulley or tub bearing. Replace the applicable component. Alternatively, there could be clothes caught between the inner and outer tubs. Read the "It spins but won't pump" section of the "It won't drain" section. Also, there could be other things that cause friction on the drive train. Seek the assistance of a qualified appliance repair technician. Siphoning If the water that pumps from the machine goes right back into the machine after the spin cycle, it may be because your washer is siphoning the water from a laundry tub with a slow drain, back into the washer. Try to improve the draining of the laundry tub. (Is there something stuck in the drain?) Also, be sure the drain hose doesn't reach more than about 4 inches into the laundry tub. If it does, cut off the excess. Water-inlet valve Water-inlet valves eventually fail. One problem that may develop with a water-inlet valve is that it can no longer completely shut off when the electricity is turned off to it. Then, the valve may leak and drip water into the clothes tub--you may notice that your washer has water in it when you haven't used it for a few days. To fix this, replace the valve.

Aug 04, 2011 • Frigidaire Washing Machines

0helpful

1answer

Clothes wet after spin

Hi, if clothes are wet after spinning, check.......
Motor coupler To test the motor coupler, re-start the washer in its spin cycle. Let the machine run for a minute, and then open the lid and notice whether the tub is spinning: If it's spinning when you lift the lid, the coupler is fine. If it isn't spinning--and your machine was produced by Whirlpool you may have a broken coupler. Many Whirlpool-made washers use a small, relatively inexpensive device called a motor coupling. This plastic-and-rubber component is mounted to the shaft of the motor on one side, and to the transmission on the other. Over time, the coupler wears out and fails. When that happens, you need to replace it completely.

Spin cycle If the washer doesn't reach its proper spin speed, the clothes may be too wet at the end of a cycle. Check to be sure the load is properly balanced and run a spin cycle again. If the clothes are still wet, you may have a worn or loose belt (Maytag), a worn clutch (GE/Hotpoint), or a worn motor pulley or tub bearing. Replace the applicable component. Alternatively, there could be clothes caught between the inner and outer tubs. Read the "It spins but won't pump" section of the "It won't drain" section. Also, there could be other things that cause friction on the drive train. Seek the assistance of a qualified appliance repair technician.

Siphoning If the water that pumps from the machine goes right back into the machine after the spin cycle, it may be because your washer is siphoning the water from a laundry tub with a slow drain, back into the washer. Try to improve the draining of the laundry tub. (Is there something stuck in the drain?) Also, be sure the drain hose doesn't reach more than about 4 inches into the laundry tub. If it does, cut off the excess.

Water-inlet valve Water-inlet valves eventually fail. One problem that may develop with a water-inlet valve is that it can no longer completely shut off when the electricity is turned off to it. Then, the valve may leak and drip water into the clothes tub--you may notice that your washer has water in it when you haven't used it for a few days. To fix this, replace the valve.

Apr 13, 2011 • Whirlpool LSR8433K Top Load Washer

3helpful

2answers

Washer-dryer # wm3677HW will not dry,heats up, run, on and on

You're a moron. This unit washes and dries. That's the whole point of it. Perhaps you should do some research before answering the question. the most likely cause is the water lever sensor.

Aug 09, 2009 • LG TROMM WM2688H 4.0 cu.ft. Front Loading...

Question 2

Anonymous

Master 4,399 Answers
Posted on May 09, 2011

Anonymous

Master

Joined: Jan 07, 2011

Answers

4399

Questions

2

Helped

875705

Points

13003

Thanks for choosing FixYa and welcome.

Testimonial: "Just having someone offer suggestions or solutions is very helpful. It helps to know I am not alone in trying to resolve a problem. Love this site!"

1 more comment
Anonymous May 09, 2011

If your washer doesn't drain or spin, you may read and learn what parts may cause this. First, you will want to check your water pump. You need to make sure it is working. Make sure you check the belt on the pump. Make sure it is not broken or loose. Also, make sure your pulley is not stuck in place. Sometimes, they will stick or barely turn at all. If this is the case, you will need to replace it. If the pump, pulley, and belt are working, make sure your motor is working. You should be able to hear it if it is. If it isn't, check your lid switch. The lid switch can cause the motor to not work. It may need adjusted. If not, go ahead and change it. A bad lid switch may cause the washer to not work at all. Now, if your pump is pumping and the washer still won't spin, you will want to check your belt and clutch. Once again, the belt may be broke or loose. Check to make sure your clutch is not worn also. This may be a case of a bad lid switch again as well. You could have a bad drive motor. This is what controls spinning, draining, and agitation. You could have a broken motor coupler. Over time, they will go bad and need replaced. It is possible that your transmission is slipping or damaged. And lastly, you could have a bad basket drive or spin bearing. This is what allows the inner tub to move. If this is the case, you will probably hear loud sounds or loud banging.
Anonymous May 09, 2011

Thank you very much for your reply. My dryer had stopped working a couple of years ago and I just had to replace a belt. The washer may need a little more work but I like to tinker so this will be interesting. The water drained as it should so I'm thinking it might be the belt or pulley. It sounds like it is running as it should except it doesn't spin so the motor should be ok. I tried to turn the tub by hand but it would not budge. I had to wring out my laundry by hand and good thing my dryer works very well. I can't check into this till next week as I have a time sensitive project to get done after work hours. Thanks again for your reply.
Anonymous May 09, 2011

Glad to see you find it handy. We appreciate you as well. Thank you for the wonderful comment and thanks for using FixYa.

×

Related Topics:

When the washer gets to the spin dry cycle, the washer will pump the water out but it doesn't spin. Took all the clothes out just in case it might have been a heavy load but even empty it wouldn't spin.

1 Answer

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

My maytag centennial washer(mvwc300vw0) spins and pumps but doesn't get the clothes as dry as it used to/should? I checked the drain hoses and they are not plugged up. Is it possible the holes i

Frigidaire Affinity Front Load Washer wont drain.

My Frigidare Affinity front load washer doesn't pump water on the Normal cycle.

Water did not drain

Washing machine does not empty

I have a Whirlpool Ultimate Care II washing machine (model LSN1000JQ0). The washer will fill with water and begin to agitate. Shortly after it will stop and will not drain. I've cleaned all hoses

Washer will not spin at all no code . will drain and tumble back and forth,when it comes time to spin it turns off.

HI: My washer will not drain all the water out at the end of the wash can you help me out

Clothes wet after spin

Washer-dryer # wm3677HW will not dry,heats up, run, on and on

Not finding what you are looking for?

PAV2300 Top Load Washer

My maytag centennial washer(mvwc300vw0) spins and pumps but doesn't get the clothes as dry as it used to/should? I checked the drain hoses and they are not plugged up. Is it possible the holes i

Ask a Question

Top Maytag Washing Machines Experts

Ronny Bennett Sr.

Brad Brown

ZJ Limited

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Manuals & User Guides

Manual. user-manual-PAV2300 Top Load...

Related Topics:

When the washer gets to the spin dry cycle, the washer will pump the water out but it doesn't spin. Took all the clothes out just in case it might have been a heavy load but even empty it wouldn't spin.

1 Answer

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

My maytag centennial washer(mvwc300vw0) spins and pumps but doesn't get the clothes as dry as it used to/should? I checked the drain hoses and they are not plugged up. Is it possible the holes i

Frigidaire Affinity Front Load Washer wont drain.

My Frigidare Affinity front load washer doesn't pump water on the Normal cycle.

Water did not drain

Washing machine does not empty

I have a Whirlpool Ultimate Care II washing machine (model LSN1000JQ0). The washer will fill with water and begin to agitate. Shortly after it will stop and will not drain. I've cleaned all hoses

Washer will not spin at all no code . will drain and tumble back and forth,when it comes time to spin it turns off.

HI: My washer will not drain all the water out at the end of the wash can you help me out

Clothes wet after spin

Washer-dryer # wm3677HW will not dry,heats up, run, on and on

Not finding what you are looking for?

PAV2300 Top Load Washer

My maytag centennial washer(mvwc300vw0) spins and pumps but doesn't get the clothes as dry as it used to/should? I checked the drain hoses and they are not plugged up. Is it possible the holes i

Related Topics

Ask a Question

Popular Questions

Washer leaking water from bottom

Maytag Neptune Error COde "nd"

Want to disengage lid lock on maytag centennial

Maytag 2000 series shows error code f6 e1. How can I fix?

Maytag maxima codes F06 and E02: Tried doing a spin/rinse/drain on an empty machine. Timer seems tpo be working but cannot hear water filling or barell spin. tried to shut off and door is now locked.

Top Maytag Washing Machines Experts

Ronny Bennett Sr.

Brad Brown

ZJ Limited

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Manuals & User Guides

Manual. user-manual-PAV2300 Top Load...