Sony DVP-NS575P DVD/CD player

please check the link below:

http://www.generalmanual.com/DVD-VCRs/Sony-DVP-NS57P-B-S-DVD-CD-Single-Disc-Player.htm

on the bottom of the page after the description, you will find the Owner Manual.

please check it, it should give you all the solutions you need.

thank you.

HELLO

My advice to you is buy the original remote! Lots of these so-called UNIVERSAL types never have all functions so get the proper remote and set it up right!

The link below contains the original replacement remote control for your unit.

Sony DVPNS575P Replacement Remote Control

Get a hold of your manufacturer and verify the warranty on your cd/dvd player. I do know that if the cd's are not finalized then cd/dvd players will not be able to read them. If under warranty your manufacturer can replace it or troubleshoot the problem with you over the phone.

Its Not But you Can Make It.
Just Take Out The Dvd And
1.Power Off The Unit
2.On The Remote And Hit Display, Top Menu, Clear, Power A Menu Will appear on The Screen.
3.Select option 2 (Drive Manual Operation),
than option 4 (Tray Aging Mode). The screen will show two input lines, each with 5 digits
4. Change The Top Line To 12450
5. Then 00000 On The Second Line And Press Enter
6. The Disk Door Will Open And Close A Couple Times
7. Repeat Steps 3-5 and enter both Codes As All 00000
A Long Process But It Works.
Hope This Helps.
Sincerely,
Michael Scott

hi my name is mark, the model DVP-NS575P is a player. it will play DVD-RW-/-R, DVD+RW/+R ,DVD-VR, JPEG, CD-R/CD-RW,and MP3 discs. hope this helps. thanks for your question.

I found this region hack here Sony DVP-NS575P region code , check it out:

"Warning
The following guide describes how I managed to make my Sony DVP-NS705V DVD player multi-region.

There are no guarantees that you will be able to do the same. Be aware that you will probably void any warranty you have and possibly even break the player.

Put shortly, you proceed at your own risk.

Introduction
First of all, the Sony DVP-NS705V can be made multi-region simply by applying appropriate service codes, you do not need to install a so called "mod chip".

This supposedly applies to the entire NS-series of Sony DVD players. There are some encouraging reports out there supporting this, but nothing has been verified by me. Again, if you choose to apply this guide to any DVD player, you do so at your own risk.

If you do find that this procedure works on another model, please drop me a line at [email protected] and let me know. Include the exact model number and original region of your player.

Update: Some users have reported success on the following players:

DVP-F21 (special thanks to Garry Self for this one)
DVP-LS500
DVP-LS755
DVP-LS785
DVP-NC615
DVP-NS300
DVP-NS305
DVP-NS310
DVP-NS315
DVP-NS330
DVP-NS333
DVP-NS355
DVP-NS360
DVP-NS400
DVP-NS405
DVP-NS410
DVP-NS430
DVP-NS433
DVP-NS575
DVP-NS585
DVP-NS590
DVP-NS700
DVP-NS730
DVP-NS765
DVP-NS900
DVP-NS905
DVP-NS930
DVP-PQ1 (thanks go to Michael Joy for this one)
DVP-PQ2
RDR-GX3 (thanks to Andreas Norman)
RDR-GX7 (thanks to Daniel Tapie)
RDR-GX300
RDR-GX700
RDR-HX900
RDR-HX1000


Please note that not all players behave exactly like the NS705. For example, some players do not display "success" when hacked.

Thanks to all who have contributed.

The infrared service codes required to make the update are available on the Internet. Unfortunately, not many people have an appropriate device to enter the codes into. You basically need a programmable remote (Philips Pronto, One-For-All) or a PDA (Palm, iPAQ) with suitable software.

This guide shows you how to make the update with a regular PC equipped with an IRDA port.

The procedure

1. Download the winsamp -package from Blank Frank's site.

http://www.veg.nildram.co.uk/remote.htm

This innovative piece of software allows you to send standard home electronics IR signals using a PC IRDA port.

2. Extract the package onto a bootable DOS floppy disk.

3. Download this IR code

http://www.selen.org/files/REMOTE.TXT

file and place it in the same directory as the package above.

This file holds the five necessary IR codes converted to the format used by Blank Frank's winsamp.exe. Please do not bother Frank with questions concerning this particular procedure.

4. Boot up your PC from the floppy disk and run winsamp.exe.

If your IRDA port doesn't appear as COM2 you may override this by using an appropriate command line switch. For example, use COM1 by running 'winsamp C1'.

5. Press the 'r' key to load up the codes into winsamp.

6. Make sure your DVD player is in standby mode and your IRDA port is within range.

7. Run the IR codes from 1 to 5 by pressing Enter on each corresponding button.

8. Your DVD player should start up and display the text "SUCCESS".

9. Repeat step 7. Your player should return to standby mode.

10.Your player is now multi-region."

On the DVD remote there is a TV on/off button. Press and keep holding the button while you press 01. Now release the On/Off button. This will solve the problem

1) Turn your DVD off. 2) Use the remote control and press: 
- Display 
- Top Menu 
- Clear 
- Power 
This should power the device into Service Mode. 
3) Choose option 2 and then choose option 4. 
4) There should be two fields: Input Code and Current Code, each one with 5 chars long. 
Type: 12450 
Then push zero on all the 5 places of the first and the second field. 
Push ENTER. 
5) There should be a zero on the device display, meaning that all regions are free. 
6) Press POWER to turn it off and you're done. 

Let me know if it works!

watch the cables of YcBcR and install them correctly.