My tv on the right of the screen is blurry,with green around the images.

The TV requires thorough servicing and this might require attention by a qualified service technician.

If you have a soldering iron and a capacitor tester you can check each cap out one by one, making sure that when you put back in a good one you observe the original polarity. If a cap has blown or is leaking it is obviously bad.

Boards can be expensive and perhaps not cost effective for a repair when you can get a new set for about the same money with a warranty to boot!

Ur convergence is dead.Must replaced 2 Convergence ICS,and some or all the resistors.Know how to solders?Buy a convergence kit Tv repair World.com,Tvrepairkits.com to repair it ur self.The shop will cost u $300 for parts and labors.

Ur convergence is dead,need convergence kit.
U know how to solder right?Tries these websites for convergence kit.Tv Repair World.com,Shopjimmy.com,Ebay.com or Partstore.com

I would say the crt's are at the end of their life.

Projection TV tubes have a liquid coolant that is used to keep them from overheating. After many years the coolant in the blue and green tubes will become  cloudy and cause the screen to look dull, red/orange, etc. You may even see halos around images. 

What you will need to do is replace the coolant and clean the crt. You can get a repair kit from www.TvRepairKits.com that includes replacement coolant, photos. instructions, etc.

The tv has 2 focus adjustments for each tube, mechanical and electrical.

1. Mechanical focus is set by looking at screen from back (through inspection plate on back of most samsungs) and rotating the lens assembly on CRT. loosen wing nut and turn lens assembly to go through focus and back to best position.

Put convergence pattern on screen and manually misadjust bottom red and green lines convergence so they can be seen through inspection hole.

With back cover of TV off you can usually reach your hand up beside the lens assembly to loosen the wing nut then rotate to adjust. Green is in the middle. The focus will be obvious when you rotate and look

When you are finished make sure the foam dust protector is not over any of the lens assemblies and the wing nut is tight.

2. Electrical focus - located at front of unit. the front grille/speaker cover is removed and maybe a cover over the front crt inspection hole.

In the inspection hole there is a black plastic "Focus/screen adjust Assembly" with 2 rows of 3 controls.

One row is focus and the other is screen. The middle controls are for green with R/B on either side. Usually the controls are labelled as "focus" and "screen". You want to adjust the focus controls, one for each color. Look for the focus or screen label imprinted in the plastic. Don't play with the screen settings.

With the same misadjusted convergence pattern you can see a red, blue and green line. Adjust green focus and watch green line for best focus. Do same for other 2.

Screen adjustments are very exact and delicate. The easiest way to deal with them is to turn color off in Customer adjust menu. Put any color tone adjustments in the middle (low, med, high, put at med).

You should have a b/w picture if there are no crt or other color related faults. If it is close to B/W leave screens alone.

If the pix is too green, then the green screen setting must be reduced a small amount. Do not play with these adjustments as most TV repairrers have a difficult time adjusting them.

If focus adjustments don't help then focus control or CRT may be defective. Needs expert to determine.

easyab

http://calgaryconvergencerepair.weebly.com/convergence-ics.html

you have a shorted green CRT that is affecting the other crts the short is internat to the crt that leaves what is called retrace lines. if the set is more than three years old then replace all three guns.

http://home.earthlink.net/~oleg.filippov/ConvergenceFix.htm
http://cmpalmer.blogspot.com/2006/11/fixing-my-own-tv-part-ii.html

Convergence IC's should be replaced before any alignment is
attempted ....part # STK392-560....You need two......mount
to large heatsink...............T.