A mouse is moving white cotton like material from under the range top out the ventilation vents. how do i get the range top up? Unscrew two screws holding it in place? Also, how do i move the stove away from the wall? Thanks for your help. Joyce

This normally happens if you were maybe not using the right needle for the material you were sewing or your bottom or top tension was too loose. It will stitch fine for a while but then the bottom cotton gets so knotted up with the one from the needle, it can a totally entangled itself around the bobbin causing the top needle to stop moving. The only way to get this knot unentangled is with patience and slow but not forcefull turning of the wheel. You need to lift the pressure foot up and switch power off. Gently tuck and pull at the material under the needle whilst slowly turning the wheel back and forth. If this fails unscrew the needle from the top so it's free and lying loose on the material and continue the gentle tucking and turning of the wheel. After a while the tension will loosen enough for you to get able to remove the bobbin, cut the thread and gently pull that thread together with the material and needle still attached to it, through the top. I hope this will help.

unscrew the 2 top screw under the screen assembly then take the back panel off and unscrew the air dock and move it to the side to reach in

first check for screws or rivets holding the top on some models you have to unscrew or drill out .

In theory quite a simple job but in practice you are unlikely to complete the task without a little damage to the interior, particularly the fabric on the inside of the A pillars.

First remove the air vents from the dashboard end caps. If you peer through the vanes on the vents you will see four plastic lugs (two per side) that have to be bent inwards. Once all four are clear then the vent just slides out towards you.

Next remove the plastic panels from the end caps in the door jambs. With these and the vents out of the way you will be able to remove the screws holding the end caps on. Some are accessed from the side and some from the front through the vent aperture. Once all the screws have been removed (four per side if I remember correctly) the end caps will slide off towards you.

Finally you have to remove the dashboard top. This requires that you remove all the exposed hex screws from the top plus two smaller screws that were hidden under the dashboard end caps yo have removed. Once all the screws have been removed slide the dashboard top towards you (it moves about an inch) and then you can lift it off vertically. If it doesn't move there may be an additional fastening under central speaker grill.

With the top off you will be able to release the radio/gps unit and remove it.

Reassembly is simply the reverse process but for some reason more difficult! Have a look on U tube as there used to be some videos showing how to do it. They make it seem much easier than it is! Good luck.

call Sears if it is under 1 year old

the yellowish "staining" is a result of a bad seal. Since it is heat changing the color of the surface, you would probably have to do some damage to remove the discoloration, either like a soft abrasive scrub or other, bleach will not fix that.
Sounds like the cleaning cycle could be too long or otherwise too hot for too long? Perhaps a wipe down with a damp cloth to the interior of the oven prior to a self clean to remove any loose material may help.. Also if there are any other vents for this oven (say under one of the burners of the stove top) make sure they are kept free and clear of any blockage of air flow..
Best regards
Ck

put the door down, and unscrew all the screws inside the oven door. Be prepared for the door to come apart as you come to the last few screws.

I just found the part that I think you need. It's part no. WB7X7220
It's available through the GE parts and accessories store.

Call Dacor at 800 793 0093. They'll tell you who has the part.

Unscrew the vent at the top of the microwave(2 phillips head screws)
inside to the right you'll see another screw holding a metal panel. Unscrew this and take the panel off and you'll see the bulb, which will unscrew counter-clockwise