How to set value 08 mode code 695 set value to 0

[F14] Invalid backup counter
Has the MAIN board been replaced?

YES
Download the counter value of the SRAM board to the MAIN board in the setting mode (08-389).

Has the SRAM board been replaced?

YES
Download the counter value of the MAIN board to the SRAM board in
the setting mode (08-388).
NO
1. Check if the connector CN2 on the SRAM
board and the connector CN2 on the MAIN
board are securely connected.
2. Replace the SRAM board.
3. Replace the MAIN board.

The conditions of the PM display consist of the codes of the setting mode (08) for "the setting value
treated as a threshold of the PM display", "the counter indicating the current number of prints and
driving time" and "the setting value which determines the display conditions".

08-6190: Setting value of PM counter [process unit (K)]
08-6191 : Setting value of PM time counter [process unit (K)]
08-5554 : Setting value of PM counter [developer material (K)]
08-5555 : Setting value of PM time counter [developer material (K)]
08-5562 : Setting value of PM counter [parts other than the PM parts of the process unit]
08-5563 : Setting value of PM time counter [parts other than the PM parts of the process unit]

Clearing counter
The counter indicating "current number of prints and driving time" used for the PM display function is
reset by entering "0" in it or clearing it in the PM support mode.
Notes:
Even if "0" is entered in the PM management setting value of the setting mode (08), the
corresponding counter for the PM display is not reset. Be sure to clear the counter in the PM
support mode when the maintenance is finished.
The reset condition of each counter is as follows:
• 08-6194: Current value of PM counter [process unit (K)]
• 08-6195: Current value of PM time counter [process unit (K)]
When the current value of "CLEANER/DRUM" on the main screen or "DRUM" on the sub-screen in
the PM support mode is cleared, the counter is reset.
• 08-5568: Current value of PM time counter [developer material (K)]
• 08-5569: Current value of PM time counter [developer material (K)]
When the current value of "DEVELOPER" on the main screen or "DEVELOPER" on the sub-screen
in the PM support mode is cleared, the counter is reset.
• 08-5576: Current value of PM counter [parts other than the PM parts of the process unit]
• 08-5577: Current value of PM time counter [parts other than the PM parts of the process unit]
• 08-6225: Number of output pages (Thick paper 1)
• 08-6226: Number of output pages (Thick paper 2)
• 08-6227: Number of output pages (Thick paper 3)
• 08-6228: Number of output pages (OHP film)
• 08-6244: Counter for tab paper
• 08-6247: Counter for envelope
When the current value of "FUSER" on the main screen or "FUSER ROLLER" on the sub screen in
the PM support mode is cleared, the counter is reset.
Notes:
The following counters are cleared by executing the EPU replacement mode.
08-6194: Current value of PM counter [process unit (K)]
08-6195: Current value of PM time counter [process unit (K)]
08-5568: Current value of PM counter [developer material (K)]
08-5569: Current value of PM time counter [developer material (K)]

You can unable the control of the toner level.
You have to enter the 08 mode (press 0 and 8 keys simultaneos and turn the machine on), than enter code 695 than press start and than set the value to 0. Confirm the choise with enter key.

set the value to 0 at 08-695

Hello

Please switch off the machine, while holding down0+8 buttons switch the machine on.
When machine starts and displays [ad] input 695 and press the start button.
Input 0 and press interupt and energy saver.
Input 971 and make sure that value is 3, if it is not input 3 and then press interupt then energy saver buttons.
Switch off the machine, wait awhile then switch the machine on.


The problem should be sorted out,
Regards

turn machine off hold down 0+8 keys and switch on inpuut 695 and press print if the value is 1 make it 0 if it is 0 make it 1 save it and check 08-971 is 3

F14 Scanner unit FROM error
Was the main PWA replaced?
YES
Download the scanner total count value into the main PWA in the setting mode (08-388).
NO
Was the scanner unit or scanner control PWA replaced?
YES
Download the scanner total counter value of the main PWA into the scanner control PWA in the setting mode (08-389).
NO
1. Check if each connector between the scanner control PWA (CN6) and the main PWA (CN8)
is disconnected.
2. Check if each connector pin is removed or the harness is broken.
3. Check if any conductor pattern on the scanner control and main PWA is open- or shortcircuited.
4. Replace the scanner control PWA.
5. Replace the main PWA.

08 mode code 695 set value to 0

The toner detection is on the toner cartridge itself, where u can see the small PCB board. Try change another toner unit.