Half full of water and wont do aqnything i push a power button or start and a series of beeps occurrs thats it . i think it said UL

the lid isnt being detected as closed

the switches have a fault in them

For future reference, here is the is a procedure for
Locking/Unlocking the VSI
The VSI has a feature that enables you to
lock your power chair to prevent unauthorized use.
To lock the VSI:
1. With the VSI switched on, press and hold the on/off key. After 1 second, the VSI should beep.
2. Release the on/off key.
3. Push the joystick to the full forward position until the VSI beeps.
4. Pull the joystick to the full rearward position until the VSI beeps.
5. Release the joystick. There should be a long beep.
6. The VSI is now locked.
To unlock the VSI:
1. Press the on/off key and power on the VSI. The maximum speed/profile indicator should ripple up and down.
2. Push the joystick to the full forward position until the VSI beeps.
3. Pull the joystick to the full rearward position until the VSI beeps.
4. Release the joystick. There should be a long beep.
5. The VSI is now unlocked.

Did any water spill out under the machine? Some of them have sensors that wont let it start if they get wet.

Hi just read your posting.Now you said in your posting it does not drain before the spin cycle, but does it drain before the rinse cycle?Does your machine stop and beep and show an error code in your LCD display or if you have the other model a series of lights?Have you tried advancing the cycle to spin and pushing the start button?Please reply with additional information and I can help you track down this fault.

Hi, just read your posting.Now the possible fault could be your display board.When you turn the power on to the machine from the power point do all the lights come on and you hear an audio beep beep , then the lights go out ?If that happens, then do you push start and can not select anything else like water temp or load size?Or do a series of lights light up and it beeps indicating a fault code after you have pushed the power button? Please reply and I can guide you throe step by step the process needed to fix this problem.

You can try tripping the breaker a half dozen times or so, or else leave it unplugged/without power for a couple days. Once it is plugged back in you may have to leave it overnight and then try it, but that almost always revives it. I notice the problem when I don't use the washer/dryer once a week or don't push any buttons during that time to activate it in some way. Problem seems to occur more frequently in the winter when house is cooler.

Dear sir, How are you, I'm sending you some codes and I hope these codes will surely help you out.:)

Nokia Code & their function:

• *3370# This Nokia code activates Enhanced Full Rate Codec (EFR) - Your Nokia cell phone uses the best sound quality but talk time is reduced my approx. 5%

• #3370# Deactivate Enhanced Full Rate Codec (EFR)

• *#4720# Activate Half Rate Codec - Your phone uses a lower quality sound but you should gain approx 30% more Talk Time

• *#4720# With this Nokia code you can deactivate the Half Rate Codec

• *#0000# Displays your phones software version, 1st Line : Software Version, 2nd Line : Software Release Date, 3rd Line : Compression Type

• *#9999# Phones software version if *#0000# does not work

• *#06# For checking the International Mobile Equipment Identity (IMEI Number)

• #pw+1234567890+1# Provider Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols)

• #pw+1234567890+2# Network Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols)

• #pw+1234567890+3# Country Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols)

• #pw+1234567890+4# SIM Card Lock Status. (use the "*" button to obtain the "p,w" and "+" symbols)

• *#147# This lets you know who called you last (Only vodofone)

• *#1471# Last call (Only vodofone)

• *#21# This phone code allows you to check the number that "All Calls" are diverted to

• *#2640# Displays phone security code in use

• *#30# Lets you see the private number

• *#43# Allows you to check the "Call Waiting" status of your cell phone.

• *#61# Allows you to check the number that "On No Reply" calls are diverted to

• *#62# Allows you to check the number that "Divert If Unreachable (no service)" calls are diverted to

• *#67# Allows you to check the number that "On Busy Calls" are diverted to

• *#67705646# Phone code that removes operator logo on 3310 & 3330

• *#73# Reset phone timers and game scores

• *#746025625# Displays the SIM Clock status, if your phone supports this power saving feature "SIM Clock Stop Allowed", it means you will get the best standby time possible

• *#7760# Manufactures code

• *#7780# Restore factory settings

• *#8110# Software version for the nokia 8110

• *#92702689# Displays - 1.Serial Number, 2.Date Made, 3.Purchase Date, 4.Date of last repair (0000 for no repairs), 5.Transfer User Data. To exit this mode you need to switch your phone off then on again

• *#94870345123456789# Deactivate the PWM-Mem

• **21*number# Turn on "All Calls" diverting to the phone number entered

• **61*number# Turn on "No Reply" diverting to the phone number entered

• **67*number# Turn on "On Busy" diverting to the phone number entered
  
  
  Good Luck. :)

UL stands for an unbalance load where one side the tub is heavier than the other side.

when the code is displayed, it automatically unlocks the lid so you can go in and reposition the clothes to try and balance it. once you are done, simply press the start button again and it should continue again where it left off. if you push the stop button, it will drain the water and assume the cycle is complete.

unplugging it and replugging it in should allow you to do other wash cycles. press power and you should be able to select wash cycles.

if you still have no control, make sure you still have power at the outlet by plugging in a lamp and turning it on. if no power, find the GFI outlet that controls that outlet and reset it. if not on a GFI outlet, then check the circuit breaker panel for a popped breaker. reset it and power should now be restored.

Did you try the power on button all the way to the left?

remove edge decore trims from left and right side front of control panel
remove phillips screws from bottom corners of contol panel
remove knob from water level selector
raise control panel ~1 inch then flip over backwords on pivots
depress lock tab on right/underside of water level control body where it touches metal mount plate
rotate water level control body 45deg anti clockwise
pull body off
top side of body next to knob shaft is 1/8 hex head bolt
turn clockwise to rais water level
anticlockwise to lower water level
machine can be operated with this part not fitted so can check level. fill, adjust screw, fill will start again, adjust screw, until water level is correct
reinstall in reverse order
Incidentally, the cause is a VERY small wire spring inside the control body that is not really up to the task, and stretches over years.
Its a common occurrence, and I make this repair, on callouts, no parts required, couple times a month you may have to flip the switch to reset to get the water to restart filling