Cant open the link to setup the router - D-Link DAP-1522 Xtreme N Duo Wireless Bridge/Access Point (DAP-1522/B) Pre-802.11n

Connect a Ethernet cable from your PC directly to the router and try to open the page 192.168.1.1 with "admin" as user and password.

Connect a LAN cable from the D-Link to your computer's LANport, open a browser and enter the D-Link's configuration URL. OR open thebrowser on your laptop and enter the D-Link's configuration URL..
http://192.168.0.1
The default login = admin
The default PW = blank (just press Enter)
You can now configure the wireless settings. To secure your wireless network from unauthorized access,please click on this link and follow my instructions :-http://www.fixya.com/support/r3559128-wireless_router_security

Hi,

In order to find the wireless security page of your Dlink wireless router DIR-615 , please follow these setps

1. Open up the internet explorer in the comp in which you are online and clear the address bar and type in the number 192.168.0.1 and hit enter.

2. You will be logged into the D-Link router setup page .

3. Under the SETUP tab, in the left hand side, click on WIRELESS SETTINGS? you will find Wireless security Mode under which you can find the password for the wireless settings.

Good Luck!

Thanks in Advance!

With Regards,

Prema.

Ok here is your solution.

1. let me know your Windows operating system
2. check your Security type setting in your router
3. channel and SSID sharing
4. disable Firewall in router
   

Check your windows firewall and some anti virus who cant also block your signal.Go to setup page Belkin using 192.168.2.1

If you cant open it just reset router,go in the back of your router and locate the reset ping.
if you still cant do it just check your physical connection and go to command prompt using RUN and type CMD after ping router 192.168.2.1 and you will get a four answer and zero lose.
if you still cant do it ask me for a remote setup in your pc .

If you are able to open Belkin setup page using 192.168.2.1
Check all configurations and be sure you can setup it to wep64 bit security mode and your problem will be solved.

I think you will need to reconfigure the router.
Reset the router for 30 seconds. unplug the power and plug it back in. wait for 1 minute and now try to reconfigure the router.
You can do it manually without the CD.
Make sure that your computer is able to go online through the modem.
If your computer is able to go online through the modem
Then you need to connect the computer to the router ad the modem to the router.
open the set up page of the router and change the settings of the router according to the ISP.
Click Here for step by step by instructions

connect the router with your laptop directly with an ethernet cable.
then open an internet explorer and type http://192.168.0.1 on the address bar on the top.
the router setup setting will open and there will be a link for wireless settings and for security. you will find the key there

Not really ...


1 thing that should not be in common between your wireless and modem is GATEWAY...

Your default modem gateway will be 192.168.1.1


change your router gateway to 192.168.2.1 or 192.168.3.1

to do this ...
1. click on start menu , type cmd , enter
2. COMMAND PROMPT dialogue box opens .
3. type . IPCONFIG
3. note your Default gateway.
4. open internet explorer
5. type your default gateway in browser address
6. it will prompt you to give user ID and password .
7 Your USER ID and password is ADMIN .
8. your router setup page opens .
9 change your local IP address to 192.168.3.1 .
10. Check mark on BRIDGING MODE .
11. Disable and enable your ethernet .
12 . now try connecting to INTERNET .


It should work . .

Hey folks, try the following things. Hope it helps !

1. Connect the cable from your modem into the Internet port of the Linksys router.

2. Reset the router with the reset button for 30 seconds when the router is ON.

3. Turn the router and the modem OFF.

4. Turn the Modem On first, wait for 10 seconds and than the router.

5. Your Internet should work from the computers connectedto the router.

6. If not open the setup page of the router by typing 192.168.1.1 in and browser, the default password is admin.

7. In the setup page, below setup tab, the 3rd subtab is MAC Address Clone, Click on that and click Enable and click Clone the MAC Address.

8. Repeat Steps 3 and 4.


For more info on linksys devices, you can try these links :

http://linksysfirmwares.googlepages.com/configurations
http://linksysfirmwares.googlepages.com/wirelesssecurity


If you want to configure the Wireless on the router :

Click on the Wireless TAB, change the name [SSID].

• Connect the computer to the router.
• Open the setup page. Default password is admin.
• Change the channel to 11-2.462 GHz.
• If you want to enable wireless security, go for WEP 64 bits.

cant open this address
http://192.168.1.1
what about solution
Thank you

connect to the router by cable
http://192.168.0.1
is the routers web address, will open the menu set to set up the router, and allow access to a set of helpscreens to explain setup of the router