Can't find the "wireless remote control" on my

take it in for a proper diagnosis and quote

I don't have service mode specifications but I do have a Samsung and looked around for how to get it in service mode some time ago because the HDMI cables somehow disconnected themselves a lot. Thought it was an electronic problem but it turned out to be a parenting problem instead SO I have never used this information and can not vouch for it. I cut and paste it from a note I copied from a forum entry to use at your discretion:
First post:
To enter "Service Mode" Press the remote - control keys in this sequence :
From Standby Info-Menu-Mute-Power On
- The buttons are active in the service mode.
Remote - Control Key : Power, Arrow Up, Arrow Down, Arrow Left, Arrow Right, Menu, Enter, Number Key(0~9)
Careful though there are things you shouldn't touch in this menu.

avforums.com/forums/lcd-led-lc­d-tvs/601553-samsung-service-m­enu-research.html

Another post:
Method 1
Put TV on standby and then push in series these buttons on the remote: 'info, menu, mute, power' the TV will then turn itself on and display a menu.
Method 2
Turn the power off. On the remote, press Mute followed by 1, 8, 2, Power in sequence.
Method 3
With the TV in standby, press the {DISPLAY} {P.STD} {MUTE} {POWER} on the remote.
Method 4
With the TV in standby, press the {SLEEP} {P.STD} {MUTE} {POWER} on the remote.
Method 5
With the TV in standby, press the {DISPLAY} {MENU} {MUTE} {POWER} on the remote.
Method 6
With the TV in standby. On the remote, press Mute followed by 1, 1, 9, Enter in sequence.
Samsung LCD Monitor Service Menu Instructions

End quote.
Good luck. Just a basic suggestion you probably don't need: keep track of any changes made by writing them down so you can put it all back if you have to.

Look for anything blocking in the sensor panel of the TV, like glue, gum or any other sticky substance, which might obscure communication. If these are ok, the sensor part has to be looked into.

For my Cisco remote (Hawaiian Telecon) the Samsung Series 45 LED TV code is 1073. Aloha

Well, you may have problem inside the TV, to find out for sure is to use this remote with SAMSUNG TV in the store where you bought it from, if it works, then I would demand them to give you a new TV since it may be a LEMON set which I would not want to own if it breaks down already, if the remote does not work in the store then ask the store to give you a new one.

Please leave rating if it helps.

No simple answer. I have the series 9 samsung.

Basically you need to connect the tv to the internet, and the remote control to the internet and then connect the remote to the tv. There are a few other ways but this is what I did for my Series 9 TV: Before you start check your wireless internet security number for your broadband router. If unsure check the instructions that came with your wireless router as you will need to type in the internet address and setup wireless security key, otherwise your exposed to other people using your broadband download.

Step One: Menu setting on TV go to PlugPlay- Network - set it up. To find Menu TV Control on remote, flick your finger right to left to scroll to new hidden screen - menu appears! Step Two: Test network connection, (you should set up wireless security (WEP/WAP) to match your broadband security key) Step Three: Services Tab/Setting icon/remote settings/network/wait until it finds network/select network/add security internet WEP/WAP Key - check IP Service Provider if unsure. When Remote is connected to the internet tap bottom right button to connect tv. Tab appears on the tv 'allow or not allow remote' select allow using the TV navigation button. Simple really. Mike

This is odd.. I have a UN model, the 6000 actually and all remotes have stopped having any effect on the Television, even the units original remote. I can access every other device except the TV, it's as if the RF sensor on the TV has failed to function anymore. Let me know if you found a solution to this problem!

Hi thanks, I got the Samsung customer support desk to assit me and fix the problem.. sorry for the bother -- I thought you were a samsung support site.

You will not have any luck, The Screen only uses RF for control. As far as I know there is no IR receiver on the unit or any RS232!! A nightmare for integrating this product into universal control systems.

Samsung TV Codes: 10060, 10812, 10702, 10178, 10030, 10766, 10814, 11060, 11903.

Hope that helps!