Clock day different from date

Normally there is a Time / H, M buttons, press the time and then the H, M buttons, if there is no time button, you need to press and hold each button H = Hour M = Minute

http://www.timex.com/info/Product_Instruction_Guides_Downloads

Many downloads here, find yours.

http://www.timex.com/info/Product_Instruction_Guides_Downloads

There are two ways to find the user manual for your Timex watch.

1. Find your watch on the list below and click on the language link for your manual.

2. Find the 3-digit module number located on the caseback of most Timex products and click on the corresponding language link for that number in the Module Table at the bottom of the page.

You are very observant! Timex watches don't have a way to adjust the day.
However, if you turn the hands clockwise you will see the day advance.
So, heres the secret, follow exactly:
1. Turn the hands until the day of the week shows the day before. If today is Wednesday then turn the hands until the watch shows Tuesday
2 Adjust the date to the day before. If today is the 17th then adjust it to the 16th
3. Now pull the crown all the out and and advance the hands until the date changes to the correct date, 17 in this example. This happens at midnight. Continue the movement in a clockwise direction for a few more hours and you should see the day change to the correct day.
4. Now continue to move in a clockwise direction until you have the current time. Remember that your date/day changed at midnight so if the current time is after lunch(noon) you must continue past noon to get to the correct time. If you don't do this correctly your date will change every day at noon instead of midnight.
If you don't succeed the first time, try, try again! Good luck, Michael, Watchmaker to the Stars!

http://www.timexaudio.com/pdf/T276IB57002_55.pdf

i WAS TOLD BY TIMEX THAT IT WAS TOO OLD ...I GUESS I'LL JUST USE IT IT A DAYTIME AREA

Hi bowingman,

To use 12- or 24-hour time for your watch, please follow the instructions below.

1. Press and hold the "Set" button for 2 seconds. The "Set" button is on the lower right side.

2. Press the "Date Advance" button on the upper right side. This will reset the seconds.

3. Press the "Change Mode" button on the lower left to set the hour. The hour will flash. Press the "Date Advance" button until the correct hour is displayed.

4. Press the "Change Mode" button again to set the correct 10s unit (first digit 1 or 0) for the minutes. Press the "Date Advance" button until the correct first digit of the minutes is displayed. Repeat this step to set the second digit of the minutes.

5. Repeat Steps 1 through 4 of this section to set the year, month, date and day and whether to use 12- or 24-hour time for your watch.

6. When finished, press the "Set" button (on the lower right) to return to the current time view and lock in your settings.

Hope it helps.

Thank you for using FixYa.

Go to timexaudio.com, select SUPPORT, then select PRODUCT MANUALS.

To change the time zone press and hold the time zone button until the number after the Z in the display flases and then release the button (number will still be flashing) and then press the same buttoon and you will see the Z number change to the zone you need. The zones are printed on the top of the clock under the top lid that pops up. My problem is we are in daylight savings time and I cannot get the Eastern Time zone to let me "spring ahead one hour" for daylight saving time!

Press and hold the Clock button (far left button in group of three) until the time begins flashing on the display. Press and hold the Forward(>>) or Reverse(<<) button to set the time. Remember to watch for AM or PM. The PM indicator is in the lower right side of the display. When finished you can either press the Clock button to set the time or after about 7 seconds it will automatically set for you. A"Beep" sound confirms that the time is set.

i wind the clock hands forward until the calendar date and week day changes and then i re-wind the hands until it comes to the correct time. when i re-wind the hands, the week day goes back to the correct date and the calendar date does not go back by one day. i don't know if this is the "correct" way to do it, but it works.