The video input channel capability is erased from the auto channel set. How do I replace the video input channel onto the tv. There are only tv channels and no video input. This is for Mickey tv set DT1300-c.

Set the TV to channel 3

Hello
First of all reset the TV. for that

press and hold the POWER button
on the TV control panel for 5 or more seconds to reset the TV.
Then connect the TV tt any source like outdoor areiel or cable box etc, select the appropriate input, and retune the TV. First of all, connect it to an external antenna, and set it to autotune.

• You must configure the ANT/CABLE input source before

programming channels (-left-hand column).

• If the ANT/CABLE input signal type is set to Cable, the

automatic channel programming process erases channels

that were previously programmed into the TV's memory.

• If the ANT/CABLE input signal type is set to Antenna, the

automatic channel programming process adds newly found

channels to the existing set of programmed channels (and

does NOT erase channels that were previously

programmed into the TV's memory.) To remove an Antenna

source channel from the memory, you must manually delete

it.

• To tune the TV to a channel not programmed in the channel

memory, you must use the Channel Number buttons on the

remote control.

• Programming channels when the ANT/CABLE input is

configured for Cable will take substantially longer than when

the antenna input is configured for Antenna. This is normal;

however, once channel programming is finished, you should

not have to repeat the programming process again unless
your Cable TV service lineup changes significantly.
Find out the received channels are clear or not. If they are clear, your TV is perfect, and the input device you connects ot the TV is faulty. OK.

hi,
when you press the reset button the tv has gone to factory setting. All the settings made by you have been erased when you rested the tv. you have to set all channels by auto tinning your tv. also you have to set picture setting according to your preference, because the tv is now in factory default setting.
ok

You are probably talking about the main menu that appears when the TV is taken off the AC power outlet, to get rid of this page just turn the tv off and on again and it should give you access to what ever channel was tuned before, if your game console has an RF out, your TV should be set to channel 3 ir 4, if the console has composite outs the change the channel until the TV goes to Aux in or Video in. Retrevo.com has an instruction manual available which you can download free, just in case you need more informantion, if the channel keys do not work, then you may have to get a universal remote ,they are fairly inexpensive and will come in very handy at least for the basic functions or just have theTV worked on.

You can replace the connector or if you have a cable box with audio and video outputs on it---connect them into one of the sets of jacks on the back of the set--switch to that input and change channels with the box----you can also do the same thing with a VCR--hook the cable into it and use its video and audio output jacks to connect to the video and audio input on the back of the TV.

In this case (the VCR does not have to work except as a tuner) you will go to whatever input you connect to and use the VCR to change channels.

These are a little less easy to use but costs you nothing---I am here to help, if you have any questions or need help let me know.


SD TECH

Try hooking up the dvd player and turning it on. Then use the setup and add/erase channel feature to look thru all of the channels. On my older GE tv I found that channel 91 was the correct channel for the video input. I saw the logo for the dvd player on this channel. I just added that channel and now it works. Your channel might be different.

Check the the color system of the tv.if the tv is auto no problem
video out from playstation to video input in tv.if this is made right with proper wire.it should funtion

...................................................
Please Don't Forget To Rate "FIXYA" Me For The Help
...................................................

if your DVD player supports a HDMI cable a single cable is enough for both audio and video channel.

but both your player and TV must support HDMI.

This sounds like a hookup or programming problem.

The typical hookup is cable/satellite box output to VCR antenna/RF input, then VCR antenna/RF output to television input. Since you are able to watch pre-recorded tapes, the latter is already correct. There are other ways to connect, using the audio/video outputs of VCR to audio/video inputs of the TV. Older or low end TV sets may not have these connections.

If by chance you are using an outdoor antenna (not cable or satellite) then the antenna connects to VCR antenna/RF input and VCR output as above. You will also need to program the VCR into the stations- most late VCRs will scan for active channels, and program themselves to those channels.

I'm not sure of the capabilities of newer cable & sat boxes, but generally, you had to tune that box to the channel you wanted to record. The VCR is set to channel 3 or 4 depending on the output of the cable box.

Lastly, most VCRs of the last 10+ years require the remote to setup advanced functions, such as timed record, date & channel setup functions. The buttons on the VCR itself only do very basic functions, Stop/Play/Rewind/F-forward/Eject etc.

If you don't have the orig. remote, some universal remotes may be able to do advanced programming functions.

There could be at least two ways to hook in your VCR. The common way is to hook your VCR inline (between) the sat box output (RF or antenna) and the TV RF/antenna input. This will allow you to play the VCR/DVD & record whatever channel the sat box is set to. I'm not real familiar with the newer sat boxes, but I assume they output one channel at a time, thus, you can only record that channel. On the older cable or outdoor antenna systems, you could record one channel while watching another. Perhaps some sat boxes have this capability. You might do a Google search with the box Model number to see if an online manual can be found. The other hookup possibility is if your TV set has audio/video inputs & outputs. Hook these to the matching input/output of the VCR/DVD.