Question about Bosch Nexxt 500 WFMC3301 Front Load Washer

Upon opening the door after the washer beeped finished, I went to remove the clothes and they were still very wet. I set the dial to "Spin" to remove more water before placing in dryer. The pump actived and the drum began to spin slowly, even reversing directions. The spin speed did not hit the "MAX" speed as it has done in the past. Very little more water was removed during those 9 minutes of spinning.

1 Answer

Android Man

Level 2:

An expert who has achieved level 2 by getting 100 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Sergeant:

An expert that has over 500 points.
Expert
278 Answers

The very first thing you have to do is to open door, put hand inside washer inner tub and move tub up and down to see if there is "play" in the bearings. if inner tub moves your main bearing is bad dragging and forcing the motor controller to think there is a "unbalance" condition. also make sure you clean the water pump screen. take small round door at the lower right side and remove the screen to clean. then put it back and retest washer. if that dont work then you may have a fulty unbalance switch or motor controller.

good luck to you.

Posted on Feb 08, 2011

1 Suggested Answer

6ya staff

2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Instant Repair Help over the Phone

6ya.com

Save Time & Money by instantly connecting to...

Posted on Jan 02, 2017

Add Your Answer

Upload

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1 Answer

Where are the springs located? I have removed the front cover of Frigidaire tumble action washer, as the washer made a loud, very loud bang, it continued to work but would not finish the last spin cyc

Frigidaire Front-Loading Washer Disassembly Frigidaire Front Loading Washer Disassembly

Sep 24, 2014 | Washing Machines

2 Answers

Clothes come out musty

I would put in some bleach and clothes that can handle it without damage and run a wash cycle. Leave the door open when you are done using the machine, or at least un-latched. There are commercial products, but bleach will do the same thing. You have stuff growing on the gizzards inside the drum, and bleach will likely kill them. They like dark & humid places.. guess what... that's your washer with the door kept latched.

Aug 15, 2014 | Kenmore Elite HE5t Washer

1 Answer

I have a 10 beep continous and showing e90 on my frigidaire washer, what will i do?

E90. The E90 error code is not a common error but it may occur when the washing machine electronics get wet for some reason. This may happen if wet clothes are left in the washer for a prolonged period after the wash cycle ends or if the same load is washed repeatedly.

Basic Reset
One of the first steps whenever an error code appears on a Frigidaire washer is to perform a simple reset to the machine. To reset the washer, press and hold the "Cancel" button for 15 seconds. Then try to set a new wash cycle and press "Start." Note that any clothes that have finished washing should always be removed promptly after the cycle is done.

Feb 26, 2014 | Frigidaire Washing Machines

1 Answer

I have a whirlpool duet washer model #WFW9150WW01 no display so the codes dont help me.. My washer will not advance to the spin cycle..i watched some videos an cleaned my drain out, my clothes were still...

Unplug it and retry another cycle. If it still does not finish the cycle remove the clamp on the boot and look for another object in there.

Oct 29, 2013 | Washing Machines

1 Answer

Finished, wash and spin lights flashing. Door

I just had this problem! To get the clothes out, open door manually (follow answers on other threads here about opening toe panel and gently pulling down on door release). But as it turned out, I didn't need to remove the clothes, and now my washer is working again.

A local repairman gave me this advice over the phone. Make sure dial is switched to off. Unplug your machine, then plug it back in. Hold down the rinse and delay buttons with one hand. With the other hand, switch the dial from off to cold or warm or whatever cycle you want. All the buttons flash a few times, then just the start button flashes. The second time I tried this, my washer worked afterwards. I've done several loads today with no problem.

Jul 19, 2010 | Bosch Nexxt 100 Series WFMC1001UC Front...

1 Answer

I have a front loader washer...it was in the middle of the cycle and starting beeping. The dr (door) signal is flashing. Cloths are wet and i can't get any cycle to go now. Any suggestions?

Unplug your machine.
Open the top of the machine.
Open door
Remove the door lock assembly
Check contacts of the door switch.
Replace if faulty or try to clean with electronics cleaning solvent.

Jun 23, 2010 | Frigidaire Affinity ATF6000F Front Load...

1 Answer

I have a kenmore front load washer model 41744052500 the other day i did a load of wash and when i went to the drain cycle it worked fine but whenit went to spin it went right a couple of times then left...

tub was out of balance remove some of the heavier clothing and re spin! and in the future donlt try to run so much through it that are heavier items when they are wet

Jan 12, 2010 | Kenmore Energy Star 44092 Front Load...

1 Answer

Washer will not drain or stat new cycle, no error message

What is the make, mode # of your washer? Do you have dial or, a keyboardl controls

Apr 26, 2009 | Whirlpool Washing Machines

2 Answers

Washer will not spin and finish cycle.

on the lower rhs is a clean out door, use ascrew driver to spin the door loose and clean out the pump behind the door.

Jan 28, 2009 | Bosch Nexxt Premium WFMC6400UC Front Load...

2 Answers

Kenmore elite washer problem

sounds as if you have a drain issue, most common cause of fault is theres something stuck in the pump housing. remove the lower acess panel(3 screws along the bottom of the forn of unit) youll gain acess to the pump housing, remove the large cover to the "button trap" by uncscrewimg the cover, it will be righthin front of you in the center of machine when cover removed, im sure youll find your blockage within there

Oct 29, 2008 | Kenmore Elite 45986 Front Load Washer

Not finding what you are looking for?

View Most Popular

Nexxt 500 WFMC3301 Front Load Washer

Washing Machines

Where are the springs located? I have removed the front cover of Frigidaire tumble action washer, as the washer made a loud, very loud bang, it continued to work but would not finish the last spin cyc

Washing Machines

Open Questions:

0 Answers

check water tap..i cleanded the filter and all seems fine but check water tap appears before final cycle.

Sep 13, 2016 | Bosch Nexxt 500 WFMC3301 Front Load Washer

0 Answers

bosch washer code d06 checked harness from control module through ntc back to control panel resistance okay heater resistance is also in spec from control module to pressure sensor connection when go through error codes e-20 shows d06 and d12

Jul 13, 2016 | Bosch Nexxt 500 WFMC3301 Front Load Washer

0 Answers

Washer drum is wobbling ALOT The drum wobbles ALOT when it turns. Someone indicated that i check to see if the drum bearing is ok - but i dont know how to do that. Any suggestions?

Jan 09, 2016 | Bosch Nexxt 500 WFMC3301 Front Load Washer

0 Answers

What does the error code 0.20 mean on above referenced? Heating element taken to appliance store and it tested out ok

May 22, 2015 | Bosch Nexxt 500 WFMC3301 Front Load Washer

See all Bosch Nexxt 500 WFMC3301 Front Load Washer Questions

Ask a Question

Usually answered in minutes!

Are you a Bosch Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Have a manual for Bosch Nexxt 500 WFMC3301 Front Load Washer? Or just drag it here!

1 Answer

Android Man

1 Suggested Answer

6ya staff

Add Your Answer

Attachments: Added items

Related Questions:

Where are the springs located? I have removed the front cover of Frigidaire tumble action washer, as the washer made a loud, very loud bang, it continued to work but would not finish the last spin cyc

Clothes come out musty

I have a 10 beep continous and showing e90 on my frigidaire washer, what will i do?

I have a whirlpool duet washer model #WFW9150WW01 no display so the codes dont help me.. My washer will not advance to the spin cycle..i watched some videos an cleaned my drain out, my clothes were still...

Finished, wash and spin lights flashing. Door

I have a front loader washer...it was in the middle of the cycle and starting beeping. The dr (door) signal is flashing. Cloths are wet and i can't get any cycle to go now. Any suggestions?

I have a kenmore front load washer model 41744052500 the other day i did a load of wash and when i went to the drain cycle it worked fine but whenit went to spin it went right a couple of times then left...

Washer will not drain or stat new cycle, no error message

Washer will not spin and finish cycle.

Kenmore elite washer problem

Not finding what you are looking for?

Nexxt 500 WFMC3301 Front Load Washer

Where are the springs located? I have removed the front cover of Frigidaire tumble action washer, as the washer made a loud, very loud bang, it continued to work but would not finish the last spin cyc

Open Questions:

check water tap..i cleanded the filter and all seems fine but check water tap appears before final cycle.

bosch washer code d06 checked harness from control module through ntc back to control panel resistance okay heater resistance is also in spec from control module to pressure sensor connection when go through error codes e-20 shows d06 and d12

Washer drum is wobbling ALOT The drum wobbles ALOT when it turns. Someone indicated that i check to see if the drum bearing is ok - but i dont know how to do that. Any suggestions?

What does the error code 0.20 mean on above referenced? Heating element taken to appliance store and it tested out ok

Related Topics:

Ask a Question

Top Bosch Washing Machines Experts

Marvin

jimorris77

Dw Wooten

Are you a Bosch Washing Machine Expert? Answer questions, earn points and help others

Manuals & User Guides

1 Answer

Android Man

1 Suggested Answer

6ya staff

Add Your Answer

Attachments: Added items

Related Questions:

Where are the springs located? I have removed the front cover of Frigidaire tumble action washer, as the washer made a loud, very loud bang, it continued to work but would not finish the last spin cyc

Clothes come out musty

I have a 10 beep continous and showing e90 on my frigidaire washer, what will i do?

I have a whirlpool duet washer model #WFW9150WW01 no display so the codes dont help me.. My washer will not advance to the spin cycle..i watched some videos an cleaned my drain out, my clothes were still...

Finished, wash and spin lights flashing. Door

I have a front loader washer...it was in the middle of the cycle and starting beeping. The dr (door) signal is flashing. Cloths are wet and i can't get any cycle to go now. Any suggestions?

I have a kenmore front load washer model 41744052500 the other day i did a load of wash and when i went to the drain cycle it worked fine but whenit went to spin it went right a couple of times then left...

Washer will not drain or stat new cycle, no error message

Washer will not spin and finish cycle.

Kenmore elite washer problem

Not finding what you are looking for?

Nexxt 500 WFMC3301 Front Load Washer

Where are the springs located? I have removed the front cover of Frigidaire tumble action washer, as the washer made a loud, very loud bang, it continued to work but would not finish the last spin cyc

Open Questions:

check water tap..i cleanded the filter and all seems fine but check water tap appears before final cycle.

bosch washer code d06 checked harness from control module through ntc back to control panel resistance okay heater resistance is also in spec from control module to pressure sensor connection when go through error codes e-20 shows d06 and d12

Washer drum is wobbling ALOT The drum wobbles ALOT when it turns. Someone indicated that i check to see if the drum bearing is ok - but i dont know how to do that. Any suggestions?

What does the error code 0.20 mean on above referenced? Heating element taken to appliance store and it tested out ok

Related Topics

Related Topics:

Ask a Question

Popular Questions

Why is the fault F18 error code on my bosch washing machine flashing?

E17 error code

How to reset the error codes (F21) on Bosch Maxx

Bosch Classixx 6 1200 express has an error code F21 what is it

Bosch Axxis Washer Detergent slot codes; what do they mean?

Top Bosch Washing Machines Experts

Marvin

jimorris77

Dw Wooten

Are you a Bosch Washing Machine Expert? Answer questions, earn points and help others

Manuals & User Guides