Miele dishwasher machine running & doesn't stop when prog selector knob is turned to off, start/stop button doesn't stop it. Stops only using on/off button. Seems to be emptying as pumps out water when poured in manually. May be G646 SC

H:H 80 on a Miele microwave indicates that the microwave's Keep Warm feature is in use. To end the cycle, open the microwave door or operate a selector or sensor (press a button (not the time display) or turn the selector knob). The keep warm setting runs the microwave for 15 minutes at 80W power starting 2 minutes after any program that used more the 450W of power. You can turn off the Keep Warm feature completely in the microwave settings. To change the setting, touch the menu button (arrow and three horizontal lines). Press OK and turn the selector knob until you see P9. Press OK and then turn the selector knob to change the setting. Press OK to save.

I found this in the manual for one of the Miele microwaves, http://static.appliancesconnection.com/attachments/D1418829486.pdf . on page 30. The section on changing the settings starts on page 40.

I hope this helps.

Cindy Wells

To turn on the oven, press the recessed On/Off button on the left below the rotary selector knob. Make sure that the system lock is off. (The display will show S 1 if it is on.) Press and release the function selector and rotary selector knobs if they are retracted. Rotate the function selector to the desired function icon (line up the dot). Then turn the selector knob to select the oven temperature. Press OK to start cooking.

Miele has the manual for the H 6260 BP oven on the product site on the Downloads tab: https://www.miele.com.au/domestic/ovens-1451.htm?mat=09514470&name=H_6260_BP . The direct link to the manual is https://www.miele.com.au/pmedia/ZGA/TX3587/10108150-000-01_10108150-01.pdf . See page 21 for a picture of the oven controls.

I hope this helps.

Cindy Wells

I have just had the same problem. Dishwasher on as normal, no water going in-EEEEk, did everything the manual said to clean drain pump and non return value, no change. Then I read answer above from wcredentino and low and behold, dishwasher immediately started and no call to service man tomorrow- yay, thanks 'wcredtino' However, for me, holding both buttons at once didn't work, reset occurred when I held the on/off switch down for 5 seconds- when I held it down with the start/stop button the problem persisted.

Thankyou!

hi,

Sounds like you would need a new timer which can be purchased from Miele directly or through a authorzised service agent

Hi there,

Well first of all you can check that the stopcock is opened fully or whether the water inlet hose is kinked. Check that the water inlet filter is not clogged and clean it, if necessary, as described in the operating instructions. Check that the drain pump is not clogged.

Reset the error message as follows: To cancel the error message, turn the rotary selector switch to "Stop/End" or press the "Start/Stop" switch for approx. 5 secs. Then switch the appliance off and then back on again. 

Good Luck!!

Thanks

One thing these guys did not point out is to turn the knob to STOP before starting this procedure (otherwise you will be ignored) Once done this works fine.
-- from the manual ----------------
Before rectifying the problem you must:
- Turn the programme selector to the "Stop" position.
- Switch the dishwasher off using the "On/Off" button.

Pull of the program knob. Then you should find a water-intake-time-selector to the right of the axis. Take a screwdriver and turn it slightly counter clockwise one click to increase the time and vice versa.

Here's the manual:
http://www.miele.com/manuals_pdf/Residential/Dishwashers/English_manuals/Operating_Instructions/G870_us.pdf

You have to buy descaling tablets from miele.  You turn the knob to program mode and keep pushing the enter button until you get to descaling.  You put two descaling tablets into your water reservoir and replace into unit.  Put containers under the steam valve and the hot water wand. Press enter.  Turn steam valve al the way on.  Keep an eye on the containers.  The process takes about 30 to 40 minutes.  The message will appear 'Descaling finished." Turn steam selector to O and press enter.  Display will read "rinse machine, fill watertank.  Fill tank and return to machine.  Place empty containers beneath hot water dispenser and steam nozzle again and turn steam selector fully on. Allow water to run through system completely.  When process is finished, display will read "Rinsing Finished."  Turn steam selector to O and press enter  Program selector is on Program Mode and display will read Descaling, Timrt, unit is no descaled and ready to use.  Turn program selector to on.

this can happen after inactivity. the circulation pump seal sticks and wont turn . when the dishwasher starts to fill the circulation pump is pulsed on to see if the preasure switch switches over (to see if water is getting into the dishwasher) if the pump does not turn there is no preasure and the machine stops thinking no water has entered. turn pump by hand to cure.

give me a couple of days and ill get back to you on that one.
do you need a part number for the knob?