I need two more rubber pegs for the base of my Patton heater. It only came with two. How can I get 2 more?

On google

Patton replace heating element Heaters Questions ... - Fixya

www.fixya.com > Forum > Tags > replace heating element > Heaters

Patton heaters replace heating element related questions and answers. Ask yourPatton ... I can't seem to find a phone number for the manufacturer to call for parts. Any help? ... Question about PQH307UM Electric Utility Heater. 1 Answer ...

Patton PQH307UM Electric Utility Heater Quartz elements ...

www.fixya.com > ... > Patton > Patton PQH307UM Electric Utility Heater

Patton PQH307UM Electric Utility Heater, quartz elements replacement related ...Element. Where can I find replacement quartz tube heating. Element Infrared ...

Patton PQH307UM Electric Utility Heater Element ... - Fixya

www.fixya.com > ... > Patton > Patton PQH307UM Electric Utility Heater

Patton PQH307UM Electric Utility Heater, element related issues. Get free help, solutions & advice from top Patton experts. ... The heating element is above the thermostat, and all you will see is a round disc with two wires attaching to. Ad.

Patton PUH680-U Utility Heater Replacement fan motor ...

Must be an older model heater. All the recent ones have a 3 prong plug. Especially, since the recall a couple of years ago on the PUH680-U Heater.

1. Remove the two small Phillips head screws holding the inside edge of the Taillight assy (you have to open the tailgate)

2. Pull straight back on the Taillight assy levering most of your pressure to the outside edge.
(There is two peg like things [top and bottom of the assy]stuck into a tight fitting hole in the body, so it will take some effort, as they are pretty snug..but, they should eventually pop out)

(Put a dab of vasoline on the pegs before you stick them back in, this makes future entries easier)

3. Twist each lamp base 1/4 turn CCW and the lamp base/holder will come right out of the Taillight assy.

4. While grasping the bulb, Pull straight out from the base..Insert new Bulb.
(Spray a little lubricating contact cleaner in the socket and on the bulb base, before you put the new bulb in.)

5. Add a little vinly/rubber spray protectant to the rubber gasket on the base.

6. Re-install Lamp and base into Taillight assy using a 1/4 turn CW twist of your wrist

7. Align the pegs on the Back of the Taillight assembly with the mating holes on the body.

8. Gently, but firmly smack the Taillight assy with the heel of your hand,to seat the pegs.

9. Re-install and tighten the two screws and go wipe off the finger prints and smudges from Taillight assy lens.

Your Patton Heater may be on the Voluntary Safety Recall List. For more info call Patton Electric Co. toll- free at (800) 528-6050. You will need your Model # and Serial # before calling.

Yes, there is/was a recall on some Patton Heaters, but I don't recall if your model # is one of them. For more info search Google for Patton Heater Recall Notice and you'll find the correct site.

Sorry to read about your problem, I hope this helps you out.

2 is

I tried to help you. Please help me and Rate/Vote on my response. We take the time to answer your question. take the time to rate us.Thanks and good luck

4 Thumbs - Very Helpful
3 Thumbs - Helpful
2 Thumbs - Somewhat Helpful
1 Thumb - Not Helpful

If it was banged in any way some thing got stuck to it need to inspecked it

Heater stop working found small metal piece with plastic with hook

Patton at l-800-528-6600 ext. 1722 (Arizona: l-800-352-0458 ext. 1722; Alaska l-800-528-0470 ext. 1722)

Does anyone have any info on whether the PUH682 was actually recalled?