Washer model number WFW9400VE error code F20 keeps coming up. Is there a way to reset?

Question edited for clarity.

A Miele Washer F20 error code generally means that the drain pump filter is clogged and needs to be cleaned.

Miele Washer F20 - Troubleshooting Guide - HowToFixit.Net

Videos as well

https://www.google.com/search?q=miele+washer+error+code+f20

..

he f20 (or fh) error code on a Whirlpool Front Load Washer is an indication of a water supply issue. To remove the f20 error code from the display panel, press Pause/Cancel 2 times. If that did not clear the error code, see below for what may be wrong

heres a link...https://removeandreplace.com/2016/01/12/whirlpool-washer-error-code-f20-troubleshooting-front-load-washing-machine/

Whirlpool Washer Error Code F20 Troubleshooting Front Load Washing Machine
This link will probably not help you ... but it does reinforce that many people have the same problem of trying numerous things ... but the code keeps coming back ... sounds very frustrating when you are trying to troubleshoot the issue yourself...

Whirlpool WasherDuet Repair F20 Error Code - YouTube






www.youtube.com/watch?v=kYuRQNbR9Nc

• By Mike Murphy ·



• 110,010 views ·



• Added May 11, 2011

How to Fix A Whirlpool Washer Model:Duet that gives you an F20 Error Code.

Error F20 indicates lack of water entering the machine.

Read more: http://www.ehow.com/search.html?s=+Kenmore+HE2+Plus+Front+Load+Washer++F20+error+code&skin=home&t=all#ixzz2qLeZJpIO

The F20 error deals with the water coming into the tub. The F20 code indicates the control didn't see any water enter the tub.
You say water comes in and fills up to the bottom of the door before the error appears.
There is a flow meter that tells the control water is coming into the washer. If the flow meter is faulty the error usually happens quickly.
There is a pressure switch and the clear plastic hose may be kinked or even have a small hole in it. One thing to try is to remove the top of the washer and then pull the hose off the pressure switch and blow through it towards the tub to check for obstructions in the air dome.
The drain hose should not be stuck down the standpipe to far. If the drain hose is stuck down the standpipe a siphon action ca occur. This means the water would fill and drain at the same time which might lead to the F20 error.
Check the drain line first and then remove the top of the washer to access the pressure switch and pressure hose. With the washer empty remove the hose from the pressure switch located on the right side of the washer and blow through it to clear any debris blocking the pressure hose or air trap.
Post the results along with your complete model number.

you may have something stuck in your drain pump. could also be a problem with your drain line, make sure drain hose is not kinked and is not 96" above the floor. if our drain line is ok. then remove bottom panel of washing machine. the drain pump will now be visible. turn the tab on the drain pump, make sure you have some towels, because water will be coming out, stick your hand inside and see if there is anything stuck inside.as far as the sud error code, the drain pump is designed to remove just water and not suds. If you are not using he (high efficiency) detergent and following instructions for the desired amount. you will get that code. Also this machine should activate a sud cycle to remove excessive suds

F20 is a door lock problem. Try resetting the breaker. if the code comes back replace the door lock.


The first thing I would check is the door lock switches and the wire harness.

Here are the break down diagrams for the Frigidaire range Model PLES389ECB

Pretty sure that F20 is a pump or drain error. Take a look at my article http://www.fixya.com/support/t3144835-not_draining_water_not_spinning This may help

The following provided by fixya has the solution to error F20.

Click here for detailing on F20 Error

Good luck and please do rate my answer.