no signal my decoder PVR 3001 is just shows scanning on the tv but does not playAdd a Commentno signal my decoder PVR 3001 is just shows scanning on the tv but does not playAdd a Comment
You can't post conmments that contain an email address.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
If you're not getting any sound from your DSTV decoder when connected to your Aim 60 Inch Digital UHD TV via HDMI, there are a few things you can try:
Check your TV settings: Make sure that your TV's audio settings are set correctly. Check that the volume is turned up and that the TV speakers are not muted or turned off. Also, make sure that the TV is set to receive audio through the HDMI input.
Check your DSTV settings: Make sure that your DSTV decoder is set to output audio through the HDMI connection. You can usually check this in the settings menu on the decoder.
Try a different HDMI input: If you have other HDMI inputs on your TV, try connecting the DSTV decoder to a different one to see if the problem persists. This will help to narrow down whether the issue is with the HDMI input on your TV or with the DSTV decoder.
Try a different HDMI cable: Even if you think your HDMI cable is fine, it's possible that there is an issue with it that is causing the sound problem. Try a different HDMI cable to see if that resolves the issue.
If none of these steps solve the issue, it's possible that there is a problem with the HDMI input on your TV. In that case, you may need to contact Aim customer support for further assistance or consider bringing the TV to a repair shop.
Mar 14, 2018 - However, the problem escalated now whereby my DSD 3U DSTV decoder suddenly switched off and only display an amber light in the middle ...
Solid Red This means that the decoder is in StandBy Mode, this is similar to a computer being put in sleep mode. · Solid Amber This state of the decoder means ...
PDF
The moment you connect your DStv HD Decoder, is the moment your TV viewing experience will become ... Solid AMBER = decoder is downloading software.
..
Try this qiuck solution as it works most of the time:
Switch off your DSTV Decoder or Unplug power supply cable at rear of Decoder.
Remove your Sim card and wait 90 seconds.
Switch your DSTV Decoder back on or plug Power supply cable back in at the rear of your Decoder.
Enter your Sim card and wait for your Decoder to re-scan (about 2 - 3 minutes).
Hi mfaille
I`m going to help you with your setup but first;
Which connection are you using from the sat receiver to the tv?
Coax / standard rg6 cable?
Did you try to manually add(in the menu/tuner setup/find channel/add) the channel you need ?
well, firstly. u have a sat finder!! great!! now lets see if i can teach u how to use it, when you hook it up there will always be some sort of signal, (other electronic waves in the air) the best way to check is to put ur hand in front of the LNB (the square box in front of the dish) if he signal goes down, the signal was fine to begin with, if it goes up, the dish is out, if nothing happens... dead LNB, which in my experiance, the most likely cause, dont for get to reset your decoder once you have solved the problem.. good luck
You need to put a compatible cable decoder box between the cable and TV as the sanyo will only decode analogue cable signals via the catv UHF vhf input
the digital antenna in is for digital air broadcasting signals only
well this is easier than you think, get yourself a set of RCA's (the red and white and yellow cables that DVD players come with) look behind your decoder and place them colour to colour, then behind your Amp you will read (TV IN) do the same, then with just one yellow RCA plug it into (monitor) that one will then go to the (AV input) behind your TV.. And presto!!! now set your amp input on the remote to TV and your off!! good luck
my dstv is just shows scanning on the tv but does not play
audio cable to dstv decorder
my dstv is just shows scanning on the tv but does not play
no signal my decoder PVR 3001 is just shows scanning on the tv but does not playAdd a Comment
×