Whirlpool WED5300S Electric Dryer Logo

Related Topics:

A
Anonymous Posted on Dec 26, 2010

It simply wont start. - Whirlpool WED5300S Electric Dryer

  • Gayle Ashbach
    Gayle Ashbach Dec 26, 2010

    is this a new dryer or a new problem?

×

2 Answers

Anonymous

Level 2:

An expert who has achieved level 2 by getting 100 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Vice President:

An expert whose answer got voted for 100 times.

  • Expert 332 Answers
  • Posted on Dec 26, 2010
Anonymous
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Vice President:

An expert whose answer got voted for 100 times.

Joined: Dec 24, 2010
Answers
332
Questions
0
Helped
83332
Points
825

If this is a sensor dryer put a jug of hot water balanced in the drum to open the sensor..

check to see if theres a red button on the back of the dryer if so press it to reset dryer

if still nothin new pcb

Tim Whalen

Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

  • Master 3,076 Answers
  • Posted on Dec 26, 2010
Tim Whalen
Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Joined: Jul 18, 2010
Answers
3076
Questions
0
Helped
824327
Points
9577

Http://www.partselect.com/dryer+dryer-wont-start+repair.htm

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

My 1999 Plymouth breeze wont start

Fuel, spark, air is the fire triangle... You're unfortunately missing one of those... Try simply waiting for a long time an hour or so and jump starting the car if necessary.... my guess is that you may have flooded the engine with repeated failed attempts to start the engine. That means there is too much gas and the plugs can't spark because they're too wet with fuel...
0helpful
1answer

Why car wont start on 2000 chevy impala i got new plugs new wires new module but still wont start

Your culprit is most likely an ignition coil, but could be so many different things, such as bad ground connections, bad ECU or simply the ECU fuse. Check all fuses to see if any are burned out. Check all wiring for corrosion. If your engine bay is nice and greasy that's probably NOT the problem. If it is rusty then likely a previous owner or dealer power-washed the engine compartment to make it look new. That's bad news because water pressure can get into almost any electrical device in the compartment, especially the ignition components. Check inside distributor. If you're lucky you may simply need to replace the rotor, if you have one. If not, it's an ignition coil.
0helpful
1answer

Was idling rev up backfierd wont start ?

Check to make sure the carburetor is still in the rubber coupler that conntects the carb to the head. usually a good backfire is all that it takes to pop it out. if it is - simply loosen the clamp on the side that popped out and slide it back together and retighten it. start the bike and enjoy.
0helpful
1answer

My quantum xts 50 after priming wont fire

does it start when you prime it or does it not start at all? if you prime it and it runs until the prime burns off then won't start again, try priming it again. If it starts and runs until the prime burns off again then it is a carburetor issue. It isn't supplying the engine with fuel to run after the prime is gone

If you need further help, I’m available over the phone at https://www.6ya.com/expert/kelly_69a0cf1b13789df1

Jan 20, 2013 • Garden
1helpful
1answer

Changed muffler, bike wont start

o2 sensor bad or not grounded. if you disconect the sensor it should start also. if the light bothers you on the bars you can simply buy an o2 sensor bypass plug. might be bad battery too. might wanna double check with a mechanic...:)
Jun 10, 2012 • Motorcycles
1helpful
1answer

Generac ix 2000 does not start. checked spark plug and it is good. oil good.

what a **** generator, worked for 100 hours and now wont start anymore.
did all the checks and replacing of spark plug and oil etc, simply wont start, ****, ****, ****..... service is horrible too. they just give you the runaround.
0helpful
1answer

My 1999 600 wont start smells rich it wants to start but wont also the clutch dose not have to be pulled to start and feels like if it did start it would be in gear without pulling clutch

rewaork the carb clean it out and the jets as far as the jamming situation wow if it start i gear that simply means it struck in gear or jam un jam it by checking first the cable if not there then next the gear box
0helpful
1answer
0helpful
1answer

1993 pontiac bonneville security light is flashing and wont start

when u see the security light blinking and it wont start u simply turn the switch on and leave it on till the security light stops blinking then turn the switch off and start the car up
Not finding what you are looking for?

118 views

Ask a Question

Usually answered in minutes!

Top Whirlpool Dryers Experts

Virgil Watts

Level 2 Expert

267 Answers

Brad Brown

Level 3 Expert

19187 Answers

Paul Bade

Level 3 Expert

1818 Answers

Are you a Whirlpool Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...