What type of battery charger does it need - Kodak EasyShare MD853 Digital Camera

some batteries are bad from factory, you should exchange it for another and try again. Make sure the battery voltage and type (ie. lithium, Nickel Cadmium,etc.) match the charger. If not, you can buy most replacement batteries for older models on the internet. If a second battery doesn't work - it's the charger .

If this is a newer purchase, my newer Milwaukee flashes slow for the first two beats and then quickly while it reads the battery type and then shifts to the slow flashing charge light after it determines the type. this is because it is a smart-charger and can charge different types of batteries

this scooter uses lead acid batteries

this type of battery much like a car type
uses constant voltage

like 13,8v from a car alternator

so a trickle charger is no use and wont work
as it only provides a constant current and not a constant voltage type senario for the charge up


use a car battery charger

problem solved for about a fiver....
the scooter will need eather 12v or 24volts

so you need either a car charger or a truck battery charger

at least 15 amp @ 13.8volts...

you could try the original supplier or ebay and failing that you could try searching online for a pdf manual and just buy any charger that is the correct type voltage and most importantly polarity, having looked at the bike its a childs harley type bike and is 6v 4ah and likely a sealed lead acid type so i would buy a 6v 500ma lead acid charger, if there is a charge port you will need a plug to match and you will need to check the polarity is correct or if there is easy access to the battery terminals you could just use the crocodile clips to the corresponding terminals on the battery itself there is a selection of chargers here 6V Lead Acid Battery Charger eBay a 500ma charger will charge the bike in 8hrs the higher the ah the faster it will charge but i wouldnt go much higher than 500ma without checking with the vendor that it is suitable for a 4ah battery hope this helps

Check that you have the correct battery in the charger as the charger will not charge any type of battery, only the battery type listed on the panel.

Lithium Ion batteries don't charge the same way ni-cads or ni-mh do. You need a lithium ion specific charger to charge them. (Some chargers do multiple types.)

Most old type Camcorder batteries came with a separate charger. so you can not charge that battery with the camera you need an external charger. The sort of charger that you need is a Universal charger the type that you use for Nicad batteries. What you must do is look at the value of your battery. If it is a 12 Volt Battery then you look for a charger that is for this value. That is if you can not get the original charger.

Lets solve this, one question at a time ....
First your batteries are not charging,This may be because of it siting for too long without a charge.The batteries may be so dead that your charger cannot reconize them. dont losse hope there are ways to check your batteries and charger with out spending alot of money on a tech coming over.
1) Unplug and remove your batteries from the chair
2) Find your self a charge that trickle charge
(Note: If you have a batterie charger ,trickle charge is the lowest set charge)
3) Trickle charge each batterie to about 50%
4) Install batteries back on to chair
5) Plug in chair charger
The chairs charger should come on ,and that right there tells you that you have a good charger!
The batteries that came with this chair are not bad and are considered ok to use .These type of batteries are what you call maintenance batteries ,which your always having to check if the leaking or need water.The gell type batteries are what they call non-maintenance.That you dont have to always look after but are more money.Thats why they recommend the gells so that the user doesn't have to work on there chair.

I hope that was helpful ,Happy Riding

The charger you need is Makita charger DC1801. If you do a search for "DC1801" on ebay you will find heaps of those chargers on there!

The DC1801 charger will charge the 6347D 18v 2Ah Makita NiCad pod-style battery.

it might be it might just be a fulty charger

Do you have a battery charger? If so, on mine I found a power-in little hole next to the battery power pins in the camera battery compartment. I also found the same type of power-in hole (like the ones found on a cell phone) on my battery charger. A double ended cord came with my camera. Maybe you have one, too. I plugged one end into the camera and the other end into the battery charger. Then I plugged the battery charger into an AC house outlet. This gave power to my camera. I am sure that you can find this type of double ended power cord on line or at a store.