I have a belkin Fd57330 gaming adapter version 2002uk, i have downloaded and installed the latest firmware but when i try to connect the device to my home network it wont allow me to. my security is wpa psk but when i enter the adapters web based interface and try to set it to wpa psk there is no box to enter the key, it says open, shared and wpa but when i click on it the screen goes blank for a few seconds then reverts back to its original state, the adapter can see my network because the ssid is displayed with my network. the adapter is a old one, it does not have the auto connect feature.

I will point you to the belkin support page, there you can download the latest updated drivers and software, once you have installed the new version, make sure you restart to ensure the new drivers take affect. Follow the link to: http://www.belkin.com/us/support-article?rnId=3746

From here download the correct version and install.

i recommend u try the old password.

Connected the router to the computer using the Ethernet cable.
Open internet explorer and type into the address bar http://192.168.2.1
If you get prompted for a username or password leave it blank and continue
You can input your internet settings from here, you can get them from your internet service providers website.

the error code 10 says that the device cannot start...for this purpose you need to remove the driver completely and re-install it again...check on www.belkin.com/support for driver support and latest version of drivers...you can also install the driver for windows 7 in compatibility mode...
right click on the downloaded driver file and go to properties> select compatibility tab and make a check on the checkbox"run this driver compatible for" and select the latest version of operating system for which the driver is available....

guess it may help you out...

Hi Friend,
Please follow the below mentioned steps one by one

Step 1:Check wither you have turned ON the Wireless switch in the laptop

Step 2:Try to search for wireless networks in the range from the laptop and check wither you are able to see the networks,try to connect

Step 3:Still no go,try to download the latest firmware from the website www.belkin.com/support and upload in the belkin router setup page

Step 4:Still no go,try to check the wireless adapters in the laptop is installed properly

If you have any clarification please feel free to reply back

Regards,
Ayyasam

u can try dowloading the latest firmware for the n1vision router...
here is the link.... http://en-us-support.belkin.com/app/answers/detail/a_id/503/p/328
download appropriate version and save in the hard disk.... login to router page... type 192.168.2.1 in internet explorer... password leave it blank and click submit.... click update firmware on the left....select browse and update the firmware dowloaded... after updating, login to the router page again and click on restore factory defaults(must)....your problem ll be rectified....

Should be latest drivers/firmware for card; may not have Beta versions listed.

http://en-us-support.belkin.com/app/product/detail/p/306

1.Primarily, if you use a N standard wireless router, you must go in for the same N standard adapter, to get full efficiency. You didn't mention the model no.
2.If you have any other wireless computer in your house, check with that if it also has the same issues. Try checking with new and old wireless devices.
3.If finally, you conclude that its only this Belkin adapter that is responsible for intermittent connection, then:
3a. Uninstall the Belkin adapter's utility and drivers from control panel(Add/Remove programs)
3b.Go to http://en-us-belkin.com/support and download the latest drivers for your model.
3c. Unplug the adapter and run the downloaded setup file. (Setup will walk you through from here)

But i could have helped you better if you had mentioned the model or part number along with the version of it.
Anyway, this would certainly work.

Connect the device to a different usb port. Download the newest software/drivers from the Belkin web site. Remove the old software and install the newest downloaded version. Please supply the error.

Yes, both Playstation 2 Online and Xbox Live have been tested and are known to work with both game consoles online. Do make sure that you are using the latest version of the routers firmware. To get the latest version go to http://networking.belkin.com and click on Firmware. Make sure you download both the firmware and the instructions on how to update the router. If you are already running the latest version then you do not need to perform another upgrade. To check to see if you have the latest firmware version open a web browser and type 192.168.2.1 into the address bar. Log into the router as instructed in the user manual. Once logged in choose Utilities over to the left and the choose Upgrade Firmware. It will tell you the current firmware version in there. If it is V1.20 or higher then you are OK.