I have a Tork 1101. Please advise how to set the OFF time.

The is nothing online. Ask NSI Industries if they can service it? You may even get a warranty repair if a spring boke.

TORK 1101B 24-Hour Indoor Mechanical Time Switch 40A ...

NSI Industries https://www.nsiindustries.com > product > tork-1101b...

TORK 1101B 24-Hour Indoor Mechanical Time Switch 40A 120V, SPST Outputs ; Repairable Units · Mechanical time switches can be repaired when components reach the ...

https://www.google.com/search?q=Tork+1101+parts+diagram

We are Fixya, not Tork, we just have a category for it.


..

Clean up the timer with compressed air and WD40.
If problem persists, then bad #101 120 volt clock motor probably
http://waterheatertimer.org/Tork-timers-and-manuals.html#1101
http://www.amazon.com/dp/B00AQZ78TU/?tag=waterheaterti-20

Clock motors and trippers can be replaced on Tork series timers.

Gene

If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7

120 Volt Clock motor might be bad?
Tighten the nut that holds the dial?
http://waterheatertimer.org/Tork-timers-and-manuals.html#1101

Gene

If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7

Is the dial rotating?

1) Copy following link for Tork 1101 product wiring and manuals:
http://waterheatertimer.org/Tork-timers-and-manuals.html#1101

2) Tork 1101 120Volt timer uses #101 clock motor.
If clock motor is working, then dial rotates around clockwise once each 24 hours... assuming timer is wired correctly.

3) Jan 2013, Add a comment and say what you are wiring.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7

Tork 1101 has 120Volt clock motor.
So circuit needs a neutral wire, in addition to 240Volt circuit with 2 hot wires.
Make sure brass bridge or jumper wire connects terminals L and 1.

Open following link for illustration.
http://waterheatertimer.org/images/Tork-1101-wired-to-control-240.jpg
Resources:
http://waterheatertimer.org/Tork-timers-and-manuals.html#1101

Take a moment and rate answer:
And take advantage of fixya expert assistance live.
For a price, expert works with you while you work on timer or any do-it-yourself project.
Fixya is always less expensive than a service call.

If clock is rotating on time, next suspect is P47 trippers have worn down. Trippers are made of softer metal so they wear down instead wearing down the on-off lever, and that way the timer lasts longer.
http://waterheatertimer.org/Tork-timers-and-manuals.html#1101
http://www.frontierlighting.com/find.jsp?a=1&ID=,Photo.Cells...Time.Controls,Replacement.Trippers

New replacement Tork 1101 120Volt timer can be purchased on-line at Amazon etc.
Home Depot sells the 120V GE 15306 indoor-outdoor version of Tork 1101 timer.
http://waterheatertimer.org/GE-timers-and-manuals.html#15306
Replacement timer in Intermatic is T101
http://waterheatertimer.org/How-to-wire-T104-Intermatic-timer.html#T101

Tork 1101 is a 120V mechanical dial-type timer

Tork 1100 series

To set timer, you lift and rotate dial. Line up current time with the word Time located to lower right of dial.

Next, place trippers on dial. Dark trippers are OFF and light-colored trippers are ON

Tork 1101 is 120V timer.
120V Black Hot wire from circuit breaker connects to Pole L
There is a brass bridge that connects Pole L and Pole 1 >> if this is missing, put a jumper wire that connects both Poles
120V White Neural wire from circuit breaker connects to Pole X
White wire going to Load (lights, fan, motor) connects to Pole X
Black wire going to Load connects to Pole 2

Up-vote if this information was helpful. Thanks for the feedback.

http://waterheatertimer.org/Tork-timers-and-manuals.html#1101

1) Tork 1101 has 120Volt clock motor, making this 120Volt timer.

2) 120Volt circuit has 1 black hot wire and 1 white neutral wire and 1 bare ground wire. Ground wires connect to green screw and to each other.

3) You have two cables, each cable has black, white and ground.
One cable arrives from breaker box.
One cable goes to Load (light, fan, motor, pump etc)

4) Cable arriving from breaker box:
a) Hot black connects to terminal L.
There should be a brass connector plate that connects terminals L and 1. If this plate is removed, then add a jumper wire from terminal L to terminal 1.
b) white connects to terminal X

5) Cable going to Load
a) Load black connects to terminal 2
b) Load white connects to terminal X along with other white wire.

Open following link to identify Tork timer
http://waterheatertimer.org/Tork-timers-and-manuals.html#1101

add a comment and say exactly what timer you have, and include photo of your timer and wiring.
http://www.fixya.com/support/r6568559-post_photograph_fixya_questions_answers

Open following link to identify Tork timer
http://waterheatertimer.org/Tork-timers-and-manuals.html#1101

Add a comment and say exactly what timer you have, and include photo of your timer and wiring.
http://www.fixya.com/support/r6568559-post_photograph_fixya_questions_answers