Install the printer drive again
1.
Alarm / Power light flashes orange 2 times consecutively (Load Paper / Paper Feed Error)
2.
Alarm / Power light flashes orange 3 times consecutively (Paper Jam Error / Cover Error)
3.
Alarm / Power light flashes orange 4 times consecutively (Out of Ink Error)
4.
Alarm / Power light flashes orange 7 times consecutively (Print head error)
After lighting in green, the power light flashes orange 7 times consecutively
5.
Alarm / Power light flashes orange 8 times consecutively (Waste Ink Nearly Full Error)
6.
Alarm / Power light flashes orange 6 times consecutively (Print head not detected)
7.
Power light (or Alarm and Power lights) alternate(s) between orange and green
After
long green flash, there are 2 or more alternating orange and green
flashes. There may also be a Service Error message on the computer
screen.
8.
Error No.: 1000 appears on the computer screen
9.
Error No.: 1700 appears on the computer screen
10.
Error No.: 300 appears on the computer screen
Any more details you need please reply,,,
All the best.
11.
Error number D308. Printer not found. Go to the chooser and select the printer again.
12.
ERROR: Printer is offline.
13.
ERROR: Printer not responding / This document failed to print
14.
ERROR: Processing cannot be continued because the Print Spooler service has been stopped.
15.
ERROR: This program is for 32-bit Intel-compatible platforms only
16.
Printed image is light
17.
Unable to perform or access Utility / Maintenance functions in OS X
18.
How do I change the amount of ink put on the paper?
19.
How do I use the BJ / IJ Status Monitor?
20.
Printer not detected during driver installation
×
Hi,
Based on your post "...they are not speaking to each other...", the only reason is because the printer is offline. Additionally, the flashing orange light might be indicative of a "Waste Ink Counter". The correct procedure would be to clean or replace before resetting but usually you can get away with resetting once.
1. Start with printer OFF
2. Hold down RESUME and then hold down POWER
3. Release RESUME
4. press RESUME twice, then release POWER
5. let green light blink until printhead has finished moving.
6. Select functions below with RESUME, execute with POWER
0 presses - green light - Test Print
1 press - orange light - EEPROM info print
2 presses - green light - EEPROM initialise
3 presses - orange light - reset waste ink counter.
The above was originally posted here. Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.
Good luck and kind regards.
Thank you for using FixYa.
Hi again,
Pls try:
1. Unplug from the mains for an hour or so;
2. thereafter while still unplug, try to power ON the printer a few times. The idea is to dissipate whatever stored/residual electricity is inside;
3. Press simultaneously on "Power" and "Resume", without letting go, ask somebody to plug in the printer to the mains.
Alternately, you can try:
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
Again, good luck.
×
Try reinstalling the printer driver again
2,127 views
Usually answered in minutes!
I have re-installed the printer driver, even updated it online, and get the same results from the printer.
Thank you for that. At the point where I'm supposed to let the green light blink until the head stops moving... the orange light blinks, not the green. If I push resume once and power once to execute a test print, the green light comes on but nothing happens. It is unresponsive to all the other commands, but hey, at least I have a solid green light now. More suggestions needed.
Sorry, none of that works.... I will try the off an hour suggestion.
The problem persists unchanged....
×