GE JCB909 Range - Blank display

If your Kenmore electric range model 790.9232 oven is not working and the control panel is blank, there are a few potential causes for this issue:

1. Faulty control board: The control board manages the oven's functions and if it is faulty, the oven may not work and the control panel may be blank.
2. Power supply issue: There may be a problem with the power supply to the oven such as a blown fuse or tripped circuit breaker.
3. Wiring issue: A wiring problem such as a broken wire or loose connection may be preventing power from reaching the oven.
4. Thermal fuse: The thermal fuse is a safety device that cuts off power to the oven if it overheats. If the thermal fuse has tripped, the oven will not work and the control panel will be blank.

It's best to have a professional technician diagnose the issue. They will be able to identify the specific cause of the problem and make the necessary repairs. It's also important to check the owner's manual for troubleshooting options or error codes that might be displayed on the control panel.
It is also important to check if the range is properly plugged in, or if the outlet is working properly.
https://www.repairclinic.com/RepairHelp/How-To-Fix-A-Range-Stove-Oven/18-6--/Kenmore-Oven-Won-T-Turn-On

https://www.youtube.com/watch?v=yLBpPg7dsg8

I would suspect either the sensor, item 253 on this schematic http://www.appliance-parts-warehouse.com/general-electric-parts/General-Electric-Range-Stove-Oven-Hood-Parts/General-Electric-Parts-JTP20BF1BB/General-Electric-Parts-58935.cfm or the oven control, item 16 on this schematic http://www.appliance-parts-warehouse.com/general-electric-parts/General-Electric-Range-Stove-Oven-Hood-Parts/General-Electric-Parts-JTP20BF1BB/General-Electric-Parts-58936.cfm

How to test many brands of Ranges that are flashing a F1 fault code: You have either a bad ERC (clock) or a bad touch pad.
1. Disconnect power to stove
2. Gain access to the back of the clock (electronic range control or ERC).
3. Unplug the touch pad ribbon connector from the ERC. This will be a flat wire approx. 1 1/2" to 2" wide.
4. Make sure everything is clear and will not short out when power is turned back on.
5. Turn power back on to stove.
6. Watch for the F1 and listen for the beep.
7. If you get the F1 and beep, replace the ERC.
8. If after approx. 30 minutes you do NOT get the F1 and hear the beep, replace the touch pad.

* ERC - Electronic Range Control

NOTE: Some models incorporate the touch pad and the clock as one part.

Hope helps.

Chances are, its been turned off and you have had the power turned back on... I found this out as well, that you need to 'acknowledge' the stove... press the centre button by the clock display, and this should beep.. you should then be able to have the elements turn on, and if you want, set the clock.. See the display, and there will be a small red light, that bounces round from corner to corner when you press the Mode button. ie, if the red light is next to Clock, then you can adjust the clock time etc etc.. hope this helps.. otherwise, we also had to find the Range Power switch going to the stovetop...

According to your symptoms, it appears that you will need a new electronic oven control board. If nothing on the range heats, you could have a tripped breaker on the 120 volt L2 leg of 240 volt power. This would prevent the cook top burners and the oven elements from heating.

How to test many brands of Ranges that are flashing a F1 fault code: You have either a bad ERC (clock) or a bad touch pad.

1. Disconnect power to stove
2. Gain access to the back of the clock (electronic range control or ERC).
3. Unplug the touch pad ribbon connector from the ERC. This will be a flat wire approx. 1 1/2" to 2" wide.
4. Make sure everything is clear and will not short out when power is turned back on.
5. Turn power back on to stove.
6. Watch for the F1 and listen for the beep.
7. If you get the F1 and beep, replace the ERC.
8. If after approx. 30 minutes you do NOT get the F1 and hear the beep, replace the touch pad.
   NOTE: Some models incorporate the touch pad and the clock as one part.

I have an electric oven that is turning on but not heating up. The oven, broiler, & stove top are not heating up. Any easy solutions to this?

You must check your incoming power for 220 volts. You have lost one leg of your power. Either a bad breaker or bad wall outlet or bad range cord.

Check for proper power (control panel is 120V, burners and heat element are 240V) You may have lost connection in one of hot wires causing the burners/elements not to work yet the control panel still will

clarkco

the burners on my magic chef stove work but the flame is not as high as it should be on one burner. I switched the top of the burner with another and it did not solve the problem.