Question about Magic Chef Ovens

1 Answer

I pressed self clean on magic chef ceramic range oven and get a dr code.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Magic Chef Master
  • 43,501 Answers

Hi, Before you go working too hard to get you oven to go intothe self clean mode(self destruct)....check out this tip...

Self Cleaning Oven Problem


" Wish I had read this first. I never would have used the self cleaningoption. Thanks for the info!!

Posted on Nov 28, 2010


1 Suggested Answer


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Hello, I have an older model magic chef gas stove/oven. It has a self cleaning oven option that I tried using. It didn't work, but now the lock light on the stove is still lit up as if it's still in...

most likely your latch assembly on unit has failed.... try resetting breaker to unit and make sure latch is not half opened or half closed while breaker is off... after checking reset breaker and see if this helps if not then probley going to need a new latch assembly and or possibly the control on unit... self clean on all ranges and ovens are trouble in my opinion they get entirely to hot and usually are ran to long... i know you said yours didn't work leads me to believe there may have already been damage to one of the pcb relays on the control but try the above first and you may luck out.... good luck to you

Jan 13, 2011 | Magic Chef Ovens

1 Answer

I have a magic chef range. I ran the self cleaning on the range. Now when trying to use the oven I get a F1 and a F3 code. I unplugged it for a while to reset and still have the same problem.

F1 Defective touch pad or clock (ERC) Replace touch pad or clock (ERC). Touch pad is a more common problem. Refer to F1 test at the top of this page for more information. F3 or F4 Shorted or open oven temperature sensor (RTD) Check sensor harness and harness connection between oven sensor and oven control. Replace oven temperature sensor (RTD) if wiring is ok.

Nov 25, 2010 | Magic Chef Ovens

1 Answer

Getting an F3 code

try starting self clean again then cancle it

May 05, 2010 | Magic Chef 9815 Electric Single Oven

1 Answer

Code F-3 or F-5 appears when oven heats

this is usually a temp sensor probe problem.check you wiring between the probe and the electronic control board. at room tempt check the resistance on the probe if it less than 500 ohms replace the probe.

Feb 23, 2010 | Magic Chef 9512 Electric Single Oven

1 Answer

Self cleaned a magic chef, now receiving an f1 code. the oven won't turn on. the clock works, and the stove works

This is the classic F1 error which is usually caused by a component failure in the control board. We repair a lot of this type of controller and would be happy to have a look at it for you if you can have the controller removed and sent to us.

Best Regards,

Oct 13, 2009 | Whirlpool 30" Self-Cleaning Freestanding...

2 Answers

My mom has a Magic Chef oven, model 5892VRV. It

You have 2 choices.
Replace the electronic control(clock).
Or, replace the range.(stove).

Sep 04, 2009 | Magic Chef Ovens

1 Answer

Magic chef gas oven range 6498xvs oven no longer works.

i have a magic chef gas range. broiler work, burners work, fan works when you turn the oven on, but oven does not get hot. could it be the electronic ignitor or does even have one.

May 20, 2009 | Ovens

1 Answer

Oven wont heat

That depends if the oven is electric or gas.

If it is electric, it can be heating element, temp probe, or control knob/buttons, board and wiring.

If it is gas it can be the igniter (check spark) , the thermostat, the safety valve that prevents accidental gas flow, or the control.

If the oven has self cleaning cycle, check that it is not stuck on self cleaning, try unplugging for a while and restarting self cleaning cycle in that case.

Check also What is wrong with your Range/Stove/Oven?

Mar 29, 2009 | Ovens

1 Answer

"F1" error code on Magic Chef gas range Model 3488XRA

the burners on my magic chef stove work but the flame is not as high as it should be on one burner. I switched the top of the burner with another and it did not solve the problem.

Jan 03, 2008 | Whirlpool 30" Self-Cleaning Freestanding...

Not finding what you are looking for?
Ovens Logo

Related Topics:

1,011 people viewed this question

Ask a Question

Usually answered in minutes!

Top Magic Chef Ovens Experts

Thomas F. Schneider

Level 3 Expert

2715 Answers


Level 2 Expert

111 Answers

Cindy Wells

Level 3 Expert

6046 Answers

Are you a Magic Chef Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides